Cutch Puller

4x4 CC · 07-03-2007, 08:12 PM

I got one for the cart and i cant seem th figure out how it works...Thanks

NO NO NO E-Z-GO! · 07-03-2007, 08:28 PM

For the stock Club Car clutch, you remove the bolt; insert the long end of the puller into the hole until it won't go in any more; thread in the screw/bolt type device on the puller shaft; tighten the screw/bolt thing until the clutch pops loose. I usually turn it a turn, and give it a light tap with a hammer, turn, tap....

I'm not sure if that's the kind you have, so you may want to post a picture.

4x4 CC · 07-03-2007, 08:58 PM

Its a Comet 94c heres a link to the Puller.

http://cartpartsplus.com/product_inf...dd32702f7cb20e

NO NO NO E-Z-GO! · 07-03-2007, 09:01 PM

That is the same principle.

4x4 CC · 07-03-2007, 11:05 PM

Thats what I thoughm, but the part that goes down in the shaft was way too long, so i used a drill bit, worked great, its on the new briggs!

NO NO NO E-Z-GO! · 07-04-2007, 10:44 AM

COOL! Good job! Now you should be on your way.

07-03-2007, 08:12 PM	#1
4x4 CC Frog Hunter Join Date: Dec 2006 Location: Little Rock, Ar Posts: 1,177	Cutch Puller I got one for the cart and i cant seem th figure out how it works...Thanks

07-03-2007, 08:28 PM	#2
NO NO NO E-Z-GO! Gone Wild Join Date: Dec 2006 Location: ComplainAboutNoNo'sProfile-Ville Posts: 5,076	Re: Cutch Puller For the stock Club Car clutch, you remove the bolt; insert the long end of the puller into the hole until it won't go in any more; thread in the screw/bolt type device on the puller shaft; tighten the screw/bolt thing until the clutch pops loose. I usually turn it a turn, and give it a light tap with a hammer, turn, tap.... I'm not sure if that's the kind you have, so you may want to post a picture.

07-03-2007, 08:58 PM	#3
4x4 CC Frog Hunter Join Date: Dec 2006 Location: Little Rock, Ar Posts: 1,177	Re: Cutch Puller Its a Comet 94c heres a link to the Puller. http://cartpartsplus.com/product_inf...dd32702f7cb20e

07-03-2007, 09:01 PM	#4
NO NO NO E-Z-GO! Gone Wild Join Date: Dec 2006 Location: ComplainAboutNoNo'sProfile-Ville Posts: 5,076	Re: Cutch Puller That is the same principle.

07-03-2007, 11:05 PM	#5
4x4 CC Frog Hunter Join Date: Dec 2006 Location: Little Rock, Ar Posts: 1,177	Re: Cutch Puller Thats what I thoughm, but the part that goes down in the shaft was way too long, so i used a drill bit, worked great, its on the new briggs!

07-04-2007, 10:44 AM	#6
NO NO NO E-Z-GO! Gone Wild Join Date: Dec 2006 Location: ComplainAboutNoNo'sProfile-Ville Posts: 5,076	Re: Cutch Puller COOL! Good job! Now you should be on your way.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode