|
Big Block Talk! Everything about swapping a big block engine into your cart! |
|
Thread Tools | Display Modes |
09-06-2015, 05:43 PM | #1 |
Gone Wild
Join Date: Oct 2010
Location: Pittsburgh Pa
Posts: 1,551
|
Vanguard thin head gaskets from CPP?
I'm considering the gaskets but would it be better to just have the heads cut? If so, how much?
Thanks |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-06-2015, 05:50 PM | #2 |
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: Vanguard thin head gaskets from CPP?
I've been there. Mill the heads. What size heads?
|
09-06-2015, 05:54 PM | #3 |
Gone Wild
Join Date: Oct 2010
Location: Pittsburgh Pa
Posts: 1,551
|
Re: Vanguard thin head gaskets from CPP?
|
09-06-2015, 05:57 PM | #4 |
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: Vanguard thin head gaskets from CPP?
Mill them .060" and use stock Graphoil gaskets.
|
09-06-2015, 06:01 PM | #5 |
Gone Wild
Join Date: Mar 2014
Location: Bountiful, Utah
Posts: 884
|
Re: Vanguard thin head gaskets from CPP?
what kind of improvement will we see after milling the heads?? I found a place locally that will do it for $75, Is it worth doing if the rest of the engine is stock?
|
09-06-2015, 06:07 PM | #6 |
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: Vanguard thin head gaskets from CPP?
It will increase the compression a bit. More compression is more power. Every little thing adds up.
|
09-06-2015, 06:08 PM | #7 |
Gone Wild
Join Date: Oct 2010
Location: Pittsburgh Pa
Posts: 1,551
|
Re: Vanguard thin head gaskets from CPP?
|
09-06-2015, 06:12 PM | #8 |
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: Vanguard thin head gaskets from CPP?
|
09-06-2015, 07:10 PM | #9 |
Gone Wild
Join Date: Oct 2010
Location: Pittsburgh Pa
Posts: 1,551
|
Re: Vanguard thin head gaskets from CPP?
Right now it has a dual valve springs, billet retainers, billet push rods and a advanced timing key. Governor has been removed. Planning on doing the 2bbl swap. Probably going with the 23hp cam. Maybe port the heads a bit since they will be removed for milling. I'm also planning on a better flowing exhaust. Do they sell flanges? If I was to do all these mods how much louder will it be?
|
09-06-2015, 07:28 PM | #10 |
Gone Wild
Join Date: Mar 2014
Location: Bountiful, Utah
Posts: 884
|
Re: Vanguard thin head gaskets from CPP?
check out robertsons torque tubes,
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Gaskets | Gas EZGO | |||
d & D motor with 2 thin yellow wires coming out of it | Extreme DC! | |||
87 octane ok with thin head gaskets on vanguard 23hp. | Big Block Talk! | |||
2001 gas club car, can head gaskets leak?? | Gas Club Car |