|
| |||||||
| BGW Gear | Register | Golf Cart Pics | Site Sponsors | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
| Big Block Talk! Everything about swapping a big block engine into your cart! |
  |
| | Thread Tools | Search this Thread | Display Modes |
06-25-2009, 09:03 AM
| #71 |
| Gone Wild    Join Date: Jun 2008 Location: waldo,wisconsin
Posts: 5,406
|  Re: Engine Swap sorry for the same old picture, this is using the stock cable! that rotates the throttle cam all the way. does yours look the same?  |
|  |
 Today
| |
| Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum | |
|
06-25-2009, 09:13 AM
| #72 |
| Not Yet Wild  Join Date: Apr 2008 Location: pittsburgh
Posts: 62
| Re: Engine Swap Yes That Is But My Cable Only Pulls About 1 Inch And That Is Not Enough To Pull The Spring That Goes From The Cam To The Govener Far Enough To Keep The Govener From Taken It To Idle . I Need It To Pull About Another 3/8 Of An Inch. I Was Going To To Move The Hole On The Cam In Closer To The Center But The Screw Head Will Hit Under Neath. |
|
| |
|
06-25-2009, 09:17 AM
| #73 |
| Gone Wild Join Date: Jun 2008 Location: waldo,wisconsin
Posts: 5,406
| Re: Engine Swap can't you short'in the spring on the governor? |
|
| |
|
06-25-2009, 09:21 AM
| #74 |
| Not Yet Wild Join Date: Apr 2008 Location: pittsburgh
Posts: 62
| Re: Engine Swap I Tried That But Then It Did Not Idle. Thanks Again For All Your Help. |
|
| |
|
06-25-2009, 10:09 AM
| #75 |
| Getting Wild  Join Date: Aug 2008 Location: Walled Lake MI
Posts: 147
| Re: Engine Swap Can you change/alter/grind the gov weights to get the RPM higher but still keep the gov functional. |
|
| |
|
06-25-2009, 10:13 AM
| #76 | |
| Gone Wild Join Date: Jun 2008 Location: waldo,wisconsin
Posts: 5,406
| Re: Engine Swap Quote:
| |
|
| |
|
06-25-2009, 10:17 AM
| #77 |
| Not Yet Wild Join Date: Apr 2008 Location: pittsburgh
Posts: 62
| Re: Engine Swap Thanks Again For All The Help I Will Keep Working On It I Will Let You Know What I Come Up With. |
|
| |
|
06-30-2009, 12:42 PM
| #78 |
| Not Yet Wild Join Date: Apr 2008 Location: pittsburgh
Posts: 62
| Re: Engine Swap Took To Camp Runs Good I Still Tring To Figure Out The Throttle . I Am Going To Try A Stiffer Spring Between The Govener Arm And The Throttle Cam. I Will Post Some Pictured After My Vacation. |
|
| |
|
06-30-2009, 12:46 PM
| #79 |
| Gone Wild Join Date: Jun 2008 Location: waldo,wisconsin
Posts: 5,406
| Re: Engine Swap  .................................. |
|
| |
|
07-08-2009, 10:38 PM
| #80 |
| Gone Wild  Join Date: Jun 2009 Location: Central PA
Posts: 330
| Re: Engine Swap I'm not real mechanical , but couldn't you just adjust the arm that attaches to the govener shaft? mine looks almost like it clamps on over the shaft that is grooved like a motorcycle shifter. |
|
| |
|
| ||||||
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Forum | |||
| engine swap | Gas EZGO | |||
| Engine Swap!!! | Gas Club Car | |||
| Engine Swap from 295 cc to ?????? | Gas EZGO | |||
| engine swap | Gas Yamaha | |||
| engine swap | Gas EZGO | |||
Linear Mode
