Another Clone build

doolin · 08-18-2008, 06:12 PM

If you go to Advanced Auto Parts, They have one that I believe is self regulated. 1-3 psi. You don't have to ask for it it's on a shelf. Cost is $20-$30.

scottyb · 08-18-2008, 10:20 PM

He only spent about $30 at Kragan Auto. We were talking about it and we bought the smallest volume pump for the least $ and it had plenty of delivery.

Double D · 08-18-2008, 10:31 PM

on your fuel setup do you have a T with a vent line in your vacuum line? my problem was like yours until i put the vent line in and now works like a charm.

cclingma · 08-19-2008, 07:08 AM

I do have a T but it goes to the short little line that runs between the valve cover and the air filter housing. I'm starting to wonder if I should have ran it somewhere else.
Thanks!

cclingma · 08-26-2008, 10:24 PM

I've got a little update for any potential cloners out there. My stock CC fuel pump is doing good now. It seems that I can run the vent hose to just about anywhere except that line that goes into the valve cover. It also seems that this little engine likes air. I'm running a rednecked up version of the clones stock air filter for now. I have a few jets for the carb coming and I'm planning on playing with other air filter/intake setups. I will say it's much more grin inspiring than it was. My driveway has the scars to prove the HP gain.

Mark L · 09-01-2008, 09:29 PM

Pic's we need updated pic's. Especially the driveway pic's.

cclingma · 09-02-2008, 05:43 PM

Quote:

Originally Posted by Mark L

Pic's we need updated pic's. Especially the driveway pic's.

I dropped the ball on this one and now I'm out of town. I hope to get em this weekend though.

cclingma · 09-12-2008, 05:53 AM

Quote:

Pic's we need updated pic's. Especially the driveway pic's.

Instead of pics I have a sob story. Things kindda went down the drain on me. I had taken the motor loose to remove the drive clutch. I didn't follow the old wise rule of removing the pos battery lead first and ended up smashing the pos wire between the engine block and cart frame. I thought I was going to burn my garage down cause of all the smoke. When I realized what was going on I pulled the battery leads. Came out very lucky really but my wiring is shot. Hope to get it wired back up this weekend.

scottyb · 09-12-2008, 09:21 AM

cclingma, Hope you get everything repaired soon. Good judgement comes from Experience. Experience comes from bad judgements. Thanks for sharing that valuable information with us....

TheNewGuy · 09-12-2008, 11:44 AM

Sorry to hear it man.

08-18-2008, 06:12 PM	#21
doolin Gone Wild Join Date: Jul 2008 Location: Central Illinois Posts: 193	Re: Another Clone build If you go to Advanced Auto Parts, They have one that I believe is self regulated. 1-3 psi. You don't have to ask for it it's on a shelf. Cost is $20-$30.

08-18-2008, 10:20 PM	#22
scottyb *******nutz Join Date: Dec 2007 Location: So Cal Posts: 4,683	Re: Another Clone build He only spent about $30 at Kragan Auto. We were talking about it and we bought the smallest volume pump for the least $ and it had plenty of delivery.

08-18-2008, 10:31 PM	#23
Double D Not Yet Wild Join Date: Jul 2008 Location: Corona, CA Posts: 37	Re: Another Clone build on your fuel setup do you have a T with a vent line in your vacuum line? my problem was like yours until i put the vent line in and now works like a charm.

08-19-2008, 07:08 AM	#24
cclingma Getting Wild Join Date: Jan 2008 Posts: 97	Re: Another Clone build I do have a T but it goes to the short little line that runs between the valve cover and the air filter housing. I'm starting to wonder if I should have ran it somewhere else. Thanks!
cclingma Getting Wild Join Date: Jan 2008 Posts: 97

08-26-2008, 10:24 PM	#25
cclingma Getting Wild Join Date: Jan 2008 Posts: 97	Re: Another Clone build I've got a little update for any potential cloners out there. My stock CC fuel pump is doing good now. It seems that I can run the vent hose to just about anywhere except that line that goes into the valve cover. It also seems that this little engine likes air. I'm running a rednecked up version of the clones stock air filter for now. I have a few jets for the carb coming and I'm planning on playing with other air filter/intake setups. I will say it's much more grin inspiring than it was. My driveway has the scars to prove the HP gain.
cclingma Getting Wild Join Date: Jan 2008 Posts: 97

09-01-2008, 09:29 PM	#26
Mark L Not Yet Wild Join Date: Jul 2008 Location: Charlotte, NC. Posts: 24	Re: Another Clone build Pic's we need updated pic's. Especially the driveway pic's.

09-12-2008, 09:21 AM	#29
scottyb *******nutz Join Date: Dec 2007 Location: So Cal Posts: 4,683	Re: Another Clone build cclingma, Hope you get everything repaired soon. Good judgement comes from Experience. Experience comes from bad judgements. Thanks for sharing that valuable information with us....

09-12-2008, 11:44 AM	#30
TheNewGuy Site Moderator Join Date: Dec 2006 Location: Ohio Posts: 5,619	Re: Another Clone build Sorry to hear it man.
	Ron If you can't run with the BIG DOGS...stay on the porch Please Visit Our Sponsors TheBadBoyG9 * Frame Mod * New Exhaust Marathon Project

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
Finally Finished 13hp Clone	Gas Club Car
13hp clone	Gas Club Car
What would you build ?	Electric Club Car
Want to build a new one	Golf Carts and Parts