|
Big Block Talk! Everything about swapping a big block engine into your cart! |
|
Thread Tools | Display Modes |
03-17-2014, 05:25 AM | #1 |
Just one day at a time
Join Date: Sep 2009
Location: South TX
Posts: 8,650
|
Working on a few issues !!
Well tore into the cart yesterday, I have been having a small issue with the rear end since it first went together. Is seems once I put the final two bolts into the pumpkin by the input shaft area it get harder to turn the gears. So I took it apart yesterday and swapped out a couple of parts to see if anything changed,,,nope anyone got any ideas? Donor rear end
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-17-2014, 05:27 AM | #2 |
Just one day at a time
Join Date: Sep 2009
Location: South TX
Posts: 8,650
|
Re: Working on a few issues !!
|
03-17-2014, 05:29 AM | #3 |
Just one day at a time
Join Date: Sep 2009
Location: South TX
Posts: 8,650
|
Re: Working on a few issues !!
|
03-17-2014, 05:31 AM | #4 |
Just one day at a time
Join Date: Sep 2009
Location: South TX
Posts: 8,650
|
Re: Working on a few issues !!
|
03-17-2014, 05:53 AM | #5 |
Just one day at a time
Join Date: Sep 2009
Location: South TX
Posts: 8,650
|
Re: Working on a few issues !!
Ok, another thought I have been reading trying to determine the right answer but I just can't seem to get the one. I have considered going to a 2bbl setup but finding an older carb with the black tube is not as easy, also I have read some on the Mikuni carbs but not sure if I should go to a single which I have seen a 38 to 40mm suggested and something about 38mm flat side??? Any help in this area would be helpful....
|
03-17-2014, 06:26 AM | #6 |
Gone Wild
Join Date: Nov 2012
Posts: 567
|
Re: Working on a few issues !!
To take the driven clutch apart all you have to do is remove the snap ring but be advised there is a spring under it and you should mark the two haves so that you can clock it in the right position when going back together.
The differential looks like it has a hole in the housing? And the hubs I read need a torque of 90-95 ft lbs. Here is a link to the carb.http://www.bikebandit.com/mikuni-tm-...&utm_campaign= |
03-17-2014, 06:29 AM | #7 | |
Just one day at a time
Join Date: Sep 2009
Location: South TX
Posts: 8,650
|
Re: Working on a few issues !!
Quote:
As far as the carb goes, since that is single will I see a difference from the stock carb and will it mount to the engine? |
|
03-17-2014, 06:45 AM | #8 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: Working on a few issues !!
Did the axle spin freely before disassembly? Maybe the parts you swapped out weren't any good, sticky bearings? Definitely doesn't sound right.
|
03-17-2014, 06:58 AM | #9 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
Re: Working on a few issues !!
|
03-17-2014, 07:04 AM | #10 |
Gone Wild
Join Date: Nov 2012
Posts: 567
|
Re: Working on a few issues !!
Not sure of the carbs performance but it will support an accelerator pump for better throttle response. Here is a sight that sells them for the mud motors may want to call them.
http://www.backwaterperformancesyste...042%20Hor.html |
|
|
Similar Threads | ||||
Thread | Forum | |||
Possible battery issues or charger issues | Columbia ParCar | |||
DS I've been working on | Electric Club Car | |||
powerdrive 2 issues and speed issues. | Electric Club Car | |||
Car still not working | Electric Club Car | |||
trying to working out carb/throttle/linkage issues | Gas Club Car |