10-27-2014, 08:48 PM | #1 |
Getting Wild
Join Date: Mar 2009
Location: Green Cove Springs, Florida
Posts: 84
|
Drive Belts
OK, I have my VC 460 Clone pretty much dialed in, Low end power you wont believe but no top end.
My motor is running very well. but cant get very much top spreed. I believe the drive belt is to long, and wont compress the driven clutch, I am using a 10986 that I believe is the stock EZGO Belt. I have a 1357 that came with the kit but it seems to be about 4 inch's shorter, So short in fact I cannot install it. Ir there a belt available between these too extremes? Maybe 1 or 2 inches longer than the 1357 belt? Where could one obtain such a belt? Claude from Green Cove Springs Fla. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-29-2014, 11:55 PM | #2 |
Gone Wild
Join Date: Sep 2011
Location: ARIZONA
Posts: 476
|
Re: Drive Belts
|
10-31-2014, 01:03 AM | #3 |
Getting Wild
Join Date: Mar 2009
Location: Green Cove Springs, Florida
Posts: 84
|
Re: Drive Belts
I looked at all those options and it just confused the issue. Can someone just give me the number and/or a source for a belt that is 2 or so inches longer than the 1357 belt that is supplied with the VC swap kit?
Claude |
11-01-2014, 04:56 PM | #4 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: Drive Belts
1357 does not seem to reference any 1 3/16 wide belt.
|
11-11-2014, 12:59 PM | #5 |
Getting Wild
Join Date: Mar 2009
Location: Green Cove Springs, Florida
Posts: 84
|
Re: Drive Belts
It is a 10986 that caame with the VC kit. This appears to be the standard Club Car belt but is at least 2-3 inches to short for my install. The stock ez go belt is about 2-3 inches too long (won't compress the driven clutch so no top end) where can I find a belt that is someware inbetwwen these two extremes.
Claude |
11-17-2014, 07:23 PM | #6 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: Drive Belts
Maybe call CPP they have another belt, that is a 1" CC belt and there are few 1" wide belts out there. Though Geoff should know all about the kit if installed properly. 1" belts are oddballs, 1 3/16 is the standard but CC clutches must be modified to work with them and you can get many sizes in that width. Many sleds use 1 3/16, tons of sizes in those, utv, ag equipment, etc.
|
11-17-2014, 10:34 PM | #7 |
Getting Wild
Join Date: Mar 2009
Location: Green Cove Springs, Florida
Posts: 84
|
Re: Drive Belts
Vegas Carts has a 1.1x44 inch belt, this made all the difference in the world, The cart will now float along at 27-28 MPH;
Claude |
11-17-2014, 11:26 PM | #8 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: Drive Belts
Vegas is really good about helping people out he should have an answer, but there are not many 1" belts out there.
|
11-19-2014, 08:43 AM | #9 |
Gone Wild
Join Date: Oct 2010
Location: Central New York
Posts: 812
|
Re: Drive Belts
how much slack should there be on the belt?
|
11-20-2014, 05:50 PM | #10 |
Gone Wild
Join Date: Sep 2011
Location: ARIZONA
Posts: 476
|
Re: Drive Belts
about 1" of deflection from a straight edge on top.
run a straight edge between the 2 pulleys, then push down in the center with a cheap ruler. Anything over 1" and under 2" will do ok. If you mark the clutches with a sharpie (big thick line from top edge to the center) you can see how well they are functioning by how much gets rubbed off.. |
|
|
Similar Threads | ||||
Thread | Forum | |||
Longer drive belts | Clone Engine Swaps | |||
Drive Belts | Golf Carts and Parts | |||
Are ATV drive belts the same as ours? | Big Block Talk! | |||
Install Seat Belts on 08 Drive | Gas Yamaha | |||
drive belts | Lifted Golf Carts |