|
06-03-2016, 03:02 PM
|
#1 |
|
Getting Wild
Join Date: Sep 2010
Location: missouri
Posts: 148
|
new problem
cart has been running fine. today, it was hard to start.
finally got it going, but now it has a miss to the engine, and the whole cart vibrates. does this at any speed. I cant find anything loose. any suggestions. |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
06-04-2016, 10:34 AM
|
#2 |
|
Getting Wild
Join Date: Sep 2010
Location: missouri
Posts: 148
|
Re: new problem
well, I am going to pull
the engine today and run it on the bench. cant imagine that its the engine, but I don't know what else to do. |
|
|
|
|
06-04-2016, 12:04 PM
|
#3 |
|
Vegas modded 420
 Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: new problem
Miss in the engine causing vibration? I would check the valve lash, spark plug. If in the ignition it will tend to do it all the time or maybe more with more throttle. If its lack of fuel it will do it more under load, too much fuel usually black smoke comes out exhaust and it does it less when you floor it.
|
|
|
|
|
06-04-2016, 05:22 PM
|
#4 |
|
Getting Wild
Join Date: Sep 2010
Location: missouri
Posts: 148
|
Re: new problem
got the miss in the engine fixed.
just a carb adjustment. removed the belt. started the engine, still has vibration. thought maybe it was something in the rear end. removed the clutch. didn't help. |
|
|
|
|
06-04-2016, 08:32 PM
|
#5 |
|
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: new problem
Check engine mounting and mounts.
|
|
|
|
|
06-04-2016, 08:39 PM
|
#6 |
|
Getting Wild
Join Date: Sep 2010
Location: missouri
Posts: 148
|
Re: new problem
when I took the belt off and started the engine,
the clutch (comet 780) pulley got narrow towards the engine to where I can see inside the clutch. what do I do now. |
|
|
|
|
06-04-2016, 08:44 PM
|
#7 |
|
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: new problem
They do that, should pop back open. There is a post here about that but I don't have a 780. With no belt they can close too far, there is some easy way to get them back right but I don't know it offhand.
http://www.buggiesgonewild.com/clone...wide-open.html |
|
|
|
|
06-05-2016, 10:20 AM
|
#8 |
|
Getting Wild
Join Date: Sep 2010
Location: missouri
Posts: 148
|
Re: new problem
thanks sho. I checked every nut and bolt
I can find. still vibrating. could it be something in the engine. |
|
|
|
|
06-05-2016, 02:16 PM
|
#9 |
|
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: new problem
Only thing comes to mind is if balancer shaft is out of time, but that would be that way since it was put together. Something with the clutch broke inside, that can cause out of balance, but unlikely if the clutch is new/good condition.
|
|
|
|
|
06-05-2016, 03:51 PM
|
#10 |
|
Getting Wild
Join Date: Sep 2010
Location: missouri
Posts: 148
|
Re: new problem
I bought the clutch new from
vegas carts. also, when I started the engine without the belt on, the clutch opened up. I did not see anything broken inside. |
|
|
|
 |
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| another problem | Gas EZGO | |||
| Ezgo charger problem now a cart problem | Electric EZGO | |||
| Found a problem...just not THE problem. | Gas EZGO | |||
| 2 carts, 1 has problem, 1 has another problem. combine for one cart? | Gas EZGO | |||
| Good problem bad problem | Big Block Talk! | |||
Linear Mode
