07-10-2018, 03:12 PM | #1 |
Not Yet Wild
Join Date: Mar 2016
Posts: 30
|
G16a predator 670 belt??
putting a 670 in my g16, with a new 780 clutch from VC
and was wondering, if there is a belt I should have to help with clutch alignment & center to center. or is there a ctr to ctr measurement for clutches I should use. any help or suggestions would be helpful Thanks PS. cart has a 5" lift so I will be droping the frt and maybe extend reward a inch or so?? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-10-2018, 04:56 PM | #2 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,633
|
Re: G16a predator 670 belt??
There is a sticky on belt calculation in the overall big block section here
|
07-10-2018, 04:58 PM | #3 |
Crazy Ole Man
Join Date: Jan 2016
Location: Owego NY
Posts: 2,758
|
Re: G16a predator 670 belt??
There's a belt length calculator in the stickys above.
|
07-10-2018, 10:03 PM | #4 |
Not Yet Wild
Join Date: Mar 2016
Posts: 30
|
Re: G16a predator 670 belt??
I understand about the belt calculator
I thought when positioning the motor if I had a belt that was possibly the right size it would make the placement of the motor easier. Was hoping someone that did it already would say belt number fit well |
07-12-2018, 03:38 PM | #5 | |
Gone Wild
Join Date: Sep 2011
Location: ARIZONA
Posts: 476
|
Re: G16a predator 670 belt??
Quote:
Every install is different. If you set it up and you can't find a belt in that size, you can use the numbers backwards to find how far you need to move the engine one way or the other to make the belt you can find fit. 46" belt is the basic shown in the calculator, or if you have a 48" you move the center to center till it shows 48" then you know what to adjust. |
|
07-15-2018, 02:43 PM | #6 |
Not Yet Wild
Join Date: Mar 2016
Posts: 30
|
Re: G16a predator 670 belt??
Diameter of the center of the drive pulley with a belt wrapped around it in inches?
I have no belt to wrap around to measure. secondary clutch = 9" center to center max 13.38 or shorter, better clearance for oil cooler & differential so am I looking for a 1-3/16" X @ ? " belt? would like to find a common size. where to hook fuel pump pulse? would like to have pedal start. |
07-15-2018, 10:47 PM | #7 |
Not Yet Wild
Join Date: Mar 2016
Posts: 30
|
Re: G16a predator 670 belt??
ok think I have it figured out
13.125 ctr 2.4 9 44.9868 1 45.1338 Dayco HP2011 motor has its own pump going to use key start. |
07-16-2018, 04:54 AM | #8 |
Crazy Ole Man
Join Date: Jan 2016
Location: Owego NY
Posts: 2,758
|
Re: G16a predator 670 belt??
The diameter of a 780 drive clutch is 7.250
|
07-16-2018, 11:50 AM | #9 |
Gone Wild
Join Date: Sep 2011
Location: ARIZONA
Posts: 476
|
Re: G16a predator 670 belt??
inside diameter, not outside.
all the way open where the belt sits 2.4 sounds correct. The HP2011 is an easy belt to find and cheap as well. I have used it on several Yamaha builds. I have done alot of 670 swaps. cooler clearance is always tough. |
07-16-2018, 06:38 PM | #10 |
Not Yet Wild
Join Date: Mar 2016
Posts: 30
|
Re: G16a predator 670 belt??
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Predator swap belt help | Clone Engine Swaps | |||
Predator 420 drive belt | Clone Engine Swaps | |||
replacing alternator/starter belt with shorter belt | Gas Club Car | |||
92 carry all drive belt and starter belt | Gas Club Car | |||
'92 carryall with new engine, belt slips even with new belt and motor set far forward | Gas Club Car |