|
02-12-2012, 06:07 PM
|
#1 |
|
Not Yet Wild
Join Date: Jan 2012
Posts: 23
|
CarryAll2 clone
Just finished duromax clone swap in 95 cc carryall 2.
first off, you can save a lot of time, aggrivation, and money fitting your engine to use original drive belt. I found if you make an engine mount approx 4 inches high it will clear the transaxle and original belt will work out fine as long as you have a 6 inch lift. I will have to say this forum and all you guys out there helped me get through this fun adventure. Im new at this but bare with me and I can give some help to others too. |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
02-12-2012, 07:25 PM
|
#2 |
|
Not Yet Wild
Join Date: Jan 2012
Posts: 23
|
Re: CarryAll2 clone
Here's a pic.
 If you look carefully, I just used gas tank mount to remount my starter/generator. this made it quite easy and I didnt have to fab up some adapter plate. Last edited by zwayitis; 02-12-2012 at 07:33 PM.. Reason: adding info about starter generator mount |
|
|
|
|
02-12-2012, 07:29 PM
|
#3 |
|
Not Yet Wild
Join Date: Jan 2012
Posts: 23
|
Re: CarryAll2 clone
 Heres a pic of using original air box with new radiator hose bought at oreily auto parts and i removed manual choke from carb and I am using original choke on stock air box |
|
|
|
|
02-12-2012, 07:31 PM
|
#4 |
|
Not Yet Wild
Join Date: Jan 2012
Posts: 23
|
Re: CarryAll2 clone
 This is my carryall 2! |
|
|
|
|
02-13-2012, 10:44 AM
|
#5 |
|
Gone Wild
Join Date: Oct 2010
Location: Fort Worth, TX
Posts: 215
|
Re: CarryAll2 clone
Nice clean swap, looks great!
|
|
|
|
|
02-13-2012, 03:24 PM
|
#6 |
|
Getting Wild
Join Date: Oct 2011
Posts: 92
|
Re: CarryAll2 clone
Good job man looks great. Im up to my knees in my swap waiting on parts. Looks like you drilled the valve cover. Did you have problems clearing the baffle? Got any pics?
|
|
|
|
|
02-13-2012, 06:59 PM
|
#7 |
|
Not Yet Wild
Join Date: Jan 2012
Posts: 23
|
Re: CarryAll2 clone
I only drilled through top layer of valve cover to existing vent to screw my barb fitting into, once it was snug I drilled smaller hole from inside the valve cover, about an eighth inch or so. It was really easy, took about five minutes total, that was removing valve cover, drilling, install barb fitting and reinstall valve cover. I wished I would have taken pics, maybe I will take it back off and take some.
|
|
|
|
|
02-13-2012, 07:07 PM
|
#8 |
|
Not Yet Wild
Join Date: Jan 2012
Posts: 23
|
Re: CarryAll2 clone
Forgot to show my motor mount. I just cut 2 inch steel pipe, tack welded to top of original plate, made another aluminum plate to sandwich on top. (easier to cut out). used 6 inch grade 8 bolts and 1 inch rubber feet I took off an old pancake compressor. Mounted all this to engine on work bench and then lowered all down into compartment and drilled out proper holes for frame mount.
 |
|
|
|
|
02-15-2012, 02:25 AM
|
#9 |
|
Not Yet Wild
Join Date: Dec 2011
Location: Flomaton,AL.
Posts: 11
|
Re: CarryAll2 clone
Can you tell a big difference in overall performance and what's the top speed now? Your install looks great!!!
|
|
|
|
|
02-15-2012, 05:22 AM
|
#10 |
|
Gone Wild
Join Date: May 2009
Location: Eustis Fl.
Posts: 154
|
Re: CarryAll2 clone
nice job zwayitis ..... it looks like it came that way .....awesome work
|
|
|
|
 |
| Tags |
| original drive belt! |
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| 2000 Club Car Carryall2 | Gas Club Car | |||
| after lifting carryall2 | Gas Club Car | |||
| Help Me Pick A Lift Kit 01 Cc Carryall2 | Lifted Golf Carts | |||
| 6"spindle for carryall2 ? | Gas Club Car | |||
| 1999 CC Carryall2 component location | Electric Club Car | |||
Linear Mode
