lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 04-03-2015, 07:52 PM   #1
Not Yet Wild
 
Join Date: Apr 2015
Location: The Dakotas
Posts: 10
Question 2003 cc magnet / speedsensor replacement

I'm new here however I have read several posts about speed sensor issues. I have pulled the sensor, however the magnet will not come out. Can anyone help. Also I took the two screws out from each side of the sensor. Was this wrong?
grandpabill is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 04-03-2015, 09:41 PM   #2
Old Sky Soldier
 
mrgolf's Avatar
Club Car
 
Join Date: Dec 2011
Location: Kentucky
Posts: 2,974
Default Re: 2003 cc magnet / speedsensor replacement

What color is your motor?
mrgolf is offline   Reply With Quote
Unread 04-03-2015, 11:12 PM   #3
Not Yet Wild
 
Join Date: Apr 2015
Location: The Dakotas
Posts: 10
Default Re: 2003 cc magnet / speedsensor replacement

Light blue
grandpabill is offline   Reply With Quote
Unread 04-03-2015, 11:44 PM   #4
Not Yet Wild
 
Join Date: Apr 2015
Location: The Dakotas
Posts: 10
Red face Re: 2003 cc magnet / speedsensor replacement

The cars serial number starts with PQ03. I just read another post saying not to take the screws out.....I already did. How do I start fishing for the retainers?
grandpabill is offline   Reply With Quote
Unread 04-03-2015, 11:48 PM   #5
Dawg Gone Wild
 
TahoeDawgZ71's Avatar
Club Car
 
Join Date: Mar 2010
Location: Golf Car Capital of The World... Augusta, Georgia
Posts: 7,960
Default Re: 2003 cc magnet / speedsensor replacement

Quote:
Originally Posted by grandpabill View Post
The cars serial number starts with PQ03. I just read another post saying not to take the screws out.....I already did. How do I start fishing for the retainers?
Take the cap off of the motor. Go to the hardware store and find a screw that matches one of the ones you removed, but longer. About 2-3 inches long. Use it as your fishing pole. I believe it's an 8-32 screw. Once you get the long one you can screw it into the bearing retainer a little, mount the plate, and use the longer screw to position the plate while you start the small original screw. Once you tighten the original screw, remove the long one and replace it with the other original screw.
TahoeDawgZ71 is offline   Reply With Quote
Unread 04-03-2015, 11:59 PM   #6
Not Yet Wild
 
Join Date: Apr 2015
Location: The Dakotas
Posts: 10
Default Re: 2003 cc magnet / speedsensor replacement

Thank you sir. To be sure, the motor cap is at the same end as the speed sensor? Should I purchase a new magnet along with the speed sensor?
grandpabill is offline   Reply With Quote
Unread 04-04-2015, 01:38 PM   #7
Not Yet Wild
 
Join Date: Apr 2015
Location: The Dakotas
Posts: 10
Question Re: 2003 cc magnet / speedsensor replacement

I have removed 3 of the 4 bolts holding the end cap on. Cannot get enough of a grip on the 4th (1:00 position) to loosen it. 5/16, 8mm, & wd 40 have not worked. Any suggestions?
grandpabill is offline   Reply With Quote
Unread 04-04-2015, 02:47 PM   #8
Gone Wild
 
theboss20's Avatar
Harley Davidson
 
Join Date: Jun 2014
Location: Buckeye, Az
Posts: 644
Default Re: 2003 cc magnet / speedsensor replacement

You do NOT need to take the end cap off...if you remove those long bolts the motor will disassemble and you will have to pull it out to get back together! The first part of the advice was good...a longer 8-32 screw about 2 1/2" long will allow you to get the bearing retainer plate repositioned and pulled up so you can start the shorter screw...I find a small Phillips screw driver handy to help with alignment so you can get it started...then screw the shorter screw in but not tight and take the longer one out...start the second short screw if you can or return to the short Phillips to realign...once you have both short screws threaded then tighten equally and don't ever take them out again unless you decide your going to completely disassemble the motor. Good luck.
theboss20 is offline   Reply With Quote
Unread 04-04-2015, 04:32 PM   #9
Gone Wild
 
Sergio's Avatar
Club Car
 
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 4,561
Default Re: 2003 cc magnet / speedsensor replacement

This will give you a visual on what you need to do.

http://www.buggiesgonewild.com/attac..._endshield.png
Sergio is offline   Reply With Quote
Unread 04-04-2015, 05:51 PM   #10
Dawg Gone Wild
 
TahoeDawgZ71's Avatar
Club Car
 
Join Date: Mar 2010
Location: Golf Car Capital of The World... Augusta, Georgia
Posts: 7,960
Default Re: 2003 cc magnet / speedsensor replacement

I guess we all have our own methods..... I've done it my way for 14 years and I've never had a motor come apart.
TahoeDawgZ71 is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
motor magnet Electric Club Car
GE magnet replacement Electric Club Car
Speed magnet Electric Club Car
GE magnet Electric Club Car
Engine Replacement for 2003 EZ-GO ST480 Gas EZGO


All times are GMT -5. The time now is 11:03 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.