lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 10-10-2015, 03:12 PM   #21
Gone Wild
Club Car
 
Join Date: Apr 2014
Location: Oregon City, Or
Posts: 1,938
Default Re: Question about upgrading to 2 gauge wires

Hmmm, 20 bucks for a set of 2 ga. cables AND ends. I'd figure on paying that much for just for the ends. Great deal.


.
tag50 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 10-10-2015, 05:06 PM   #22
Gone Wild
 
Dale-D's Avatar
Club Car
 
Join Date: Sep 2013
Location: New Iberia, La.
Posts: 154
Default Re: Question about upgrading to 2 gauge wires

Naw, the ends here were only $.80 at the Handyman Hardware, the wire cost the most, I had the brass bolt with brass washers and the nuts.........

Scottyb has a nice set, and his bolt thru is top notch, I helped someone install a set from him, and that is why I made my own, I am a Cheap ****
Dale-D is offline   Reply With Quote
Unread 10-10-2015, 05:41 PM   #23
Dazed & Confused
 
crash test dummy's Avatar
Club Car
 
Join Date: Nov 2011
Location: Z-HELLS FL
Posts: 14,031
Default Re: Question about upgrading to 2 gauge wires

Quote:
Originally Posted by Dale-D View Post
I am a Cheap ****


a ss ...nope
bit ch ... nope
who re ... nope
ok... i give up .. what are you ?
crash test dummy is online now   Reply With Quote
Unread 10-10-2015, 07:10 PM   #24
What the.....?
 
lockman1's Avatar
Club Car
 
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 11,368
Default Re: Question about upgrading to 2 gauge wires


Last edited by lockman1; 10-10-2015 at 07:12 PM.. Reason: Nope... not gonna do it!
lockman1 is offline   Reply With Quote
Unread 10-10-2015, 09:30 PM   #25
Getting Wild
 
wards75's Avatar
Club Car
 
Join Date: Oct 2012
Location: Eastern NC
Posts: 141
Default Re: Question about upgrading to 2 gauge wires

sorry for any hijack but...what would be the best way to clean or neutralize acid flux? I got plenty of welding cable, gonna make my own too. Was gonna buy the electrical solder pellets to do it though..just curious if there is a "Cheaper" but also effective/proper way.
wards75 is offline   Reply With Quote
Unread 10-11-2015, 06:57 AM   #26
Gone Wild
 
Dale-D's Avatar
Club Car
 
Join Date: Sep 2013
Location: New Iberia, La.
Posts: 154
Default Re: Question about upgrading to 2 gauge wires

I just use the Rosen Solder Flux, since it can be left on the wires without damaging them in any way
Acid Solder Flux can be neutralized with Baking Soda and use a wire brush to remove the most of it prior to neutralizing it, and scrub it with the wire brush and baking soda water until it no longer foams, then it should be clean and acid free
Dale-D is offline   Reply With Quote
Unread 10-11-2015, 08:31 AM   #27
Gone Wild
 
glassk's Avatar
Club Car
 
Join Date: Dec 2011
Location: Hampton, GA
Posts: 441
Default Re: Question about upgrading to 2 gauge wires

While acid based fluxes are highly active, they are also hygroscopic. This means that any flux remaining after the soldering operation will acquire moisture from the atmosphere. Left intact, excess acid flux can cause moisture to accumulate to the extent that it will actually flow and puddle. Since acid fluxes usually remain active after the soldering process, removing the residue is indicated to keep the residue from continuing to eat away at the part.

Acid based fluxes are usually water soluble, which allows for easy removal with little more than warm water and a mild detergent.


http://www.cranesolder.com/faq.htm#rosinoracid
glassk is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
How to tell the gauge of my wires Electric EZGO
Upgrading to #4 gauge cables Electric Club Car
86 Ds with 1/0 gauge wires Electric Club Car
Upgrading Motor, Controller, Wires,! Electric Club Car
Upgrading Cables to 4 gauge Electric Club Car


All times are GMT -5. The time now is 07:11 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.