lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 08-11-2017, 01:23 PM   #111
Not Yet Wild
 
Join Date: Mar 2017
Posts: 9
Default Re: Bypassing Club Car IQ/Excel OBC

This is the diagram i'm going by.
Attached Images
File Type: jpg Image.jpg (106.1 KB, 0 views)
jdreher is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 08-11-2017, 01:26 PM   #112
Not Yet Wild
 
Join Date: Mar 2017
Posts: 9
Default Re: Bypassing Club Car IQ/Excel OBC

That's correct. nothing happens.
jdreher is offline   Reply With Quote
Unread 08-11-2017, 01:42 PM   #113
Gone Wild
 
Sergio's Avatar
Club Car
 
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 5,372
Default Re: Bypassing Club Car IQ/Excel OBC

We must be miscommunicating or those wires are not running the way you think they do.

Since you are getting pack voltage from B- ( I assume you meant 50.7v or 51.7v and not 57.7v) and the wire should go directly from Controller B- to the solenoid small post...

With the yellow wire connected to Controller B-, Do You get pack voltage reading from the pack positive battery post to the solenoid small post where the yellow wire is connected ?
Sergio is offline   Reply With Quote
Unread 08-11-2017, 02:18 PM   #114
Not Yet Wild
 
Join Date: Mar 2017
Posts: 9
Default Re: Bypassing Club Car IQ/Excel OBC

You're awesome Sergio! Sorry for the troubles. I was taking that yellow wire off the solenoid and putting it on B- directly. so, it was still hooked up to the OBC to B-. Now, I ran the yellow wire straight from B- to the negative side of the solenoid and it works fine. thank you!
jdreher is offline   Reply With Quote
Unread 02-06-2018, 09:03 PM   #115
Not Yet Wild
 
Join Date: Nov 2016
Posts: 2
Default Re: Bypassing Club Car IQ/Excel OBC

Hey Guys,

First time posting so bare with me please. I am a little confused with the OBC bypass. I have 2007 club car Presedent IQ. I am in the middle of upgrade to XCT 500 alltrax controller, wires, 400 amp solenoid,A4 motor. Bad *** I know. Ha.
Any way i also purchased a new charger the Uy series and would like to bypass the OBC. I noticed Neg pack wire running thru the OBC to the controller. Do I still need to do this? can you also go over the Blue wire connection again

Thanks, Jim
Attached Images
File Type: jpg IMG_5479.jpg (217.1 KB, 0 views)
File Type: jpg IMG_5435.jpg (216.2 KB, 0 views)
jamesrock@me.com is offline   Reply With Quote
Unread 02-07-2018, 05:49 AM   #116
Gone Wild
 
Sergio's Avatar
Club Car
 
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 5,372
Default Re: Bypassing Club Car IQ/Excel OBC

You can disconnect and totally remove the OBC from the cart.

With an XCT500 You should be upgrading your cables to 4ga or 2ga anyway so that will allow you to run the new negative cable easier.

Remember to run the 12ga negative wire from the charger receptacle directly to pack negative battery post.


Also, specific to the Alltrax XCT, you do not need to jump any wires on the OBC connector, just unplug it.

Go to the Alltrax Software and set:
Disable the Controller when interlock input signal (user 3) is: High/Low
Sergio is offline   Reply With Quote
Unread 02-07-2018, 04:47 PM   #117
Not Yet Wild
 
Join Date: Nov 2016
Posts: 2
Default Re: Bypassing Club Car IQ/Excel OBC

Thanks, I will give it a run tomorrow.
jamesrock@me.com is offline   Reply With Quote
Unread 02-22-2018, 09:33 PM   #118
Not Yet Wild
 
Join Date: Jan 2010
Posts: 63
Default Re: Bypassing Club Car IQ/Excel OBC

I have a 05 Precedent. The wiring has been modified, I know a tail light kit has been removed at the very least, Please see the attachment. I'm in the process of removing the OBC and converting from 4x12 to 6x8. Which wiring diagram do I use as none match up precisely.

Serial drive by-pass

Regen-1 by-pass

Regen-2 by-pass

or do I have a oddball cart and none will work. I could just bypass it at the controller. I assume the reason for using the pin method from the controller is if one wanted at add the OBC back in no re-wiring would be required?
Attached Images
File Type: jpg IMG_4436.jpg (224.5 KB, 0 views)
mlanierjr is offline   Reply With Quote
Unread 02-23-2018, 06:15 AM   #119
Gone Wild
 
Sergio's Avatar
Club Car
 
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 5,372
Default Re: Bypassing Club Car IQ/Excel OBC

Just use the instructions on the first post, they are designed for any IQ or Excell cart.

This should be your wiring diagram:



You can just cut the Light-Blue and the White wires in the harness right before the OBC 6-pin connector and splice those 2 wires together.

You also need to make sure the 10ga negative wire from the charger receptacle goes directly to the pack negative battery post.
Sergio is offline   Reply With Quote
Unread 02-23-2018, 07:54 AM   #120
Not Yet Wild
 
Join Date: Jan 2010
Posts: 63
Default Re: Bypassing Club Car IQ/Excel OBC

Thank You! Just the one I needed.
mlanierjr is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
Bypassing Club Car IQ OBC Electric Club Car
95 club car 48v wont run without bypassing solonoid Electric Club Car
Bypassing relay in club car charger Electric Club Car
Bypassing the OBC on 96 DS club Car. Electric Club Car
bypassing OBC on 2002 Club Car Electric Club Car


All times are GMT -5. The time now is 03:22 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.