lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 05-12-2016, 05:50 PM   #1
Gone Wild
 
Join Date: Apr 2014
Posts: 220
Default where to land the motor leads terminals not marked

ok guys I got this 36 volt motor I am going to try this in my 2001 48 volt series cart. the terminals are not marked can someone tell me what wires are landed where?
Thanks
the other motor I was looking at was a 16 spline and the wrong axle. this motor wont come off but is the right axle so I am going to swap it all.
thanks
Attached Images
File Type: jpg IMG_3369[1].jpg (132.6 KB, 0 views)
cjpenny89 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 05-12-2016, 06:29 PM   #2
Gone Wild
Yamaha
 
Join Date: May 2012
Location: Rio Verde, Az
Posts: 2,684
Default Re: where to land the motor leads terminals not marked

You need to determine which terminals are Armature and which are Field. Then you can wire it correctly. At least figure out with an ohmmeter which terminal is paired with which. You will read continuity between the pairs but not between them.
Volt_Ampere is offline   Reply With Quote
Unread 05-12-2016, 06:32 PM   #3
Gone Wild
 
Join Date: Apr 2014
Posts: 220
Default Re: where to land the motor leads terminals not marked

I know which one are brushes and which ones are the magnets. does that help?
cjpenny89 is offline   Reply With Quote
Unread 05-12-2016, 06:33 PM   #4
Cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 64,093
Default Re: where to land the motor leads terminals not marked

There should be stamped S1 A1 etc in the case..... it should match this tech bulletin below
Attached Images
File Type: jpg pg 101980s-CC-.jpg (61.0 KB, 0 views)
scottyb is offline   Reply With Quote
Unread 05-12-2016, 06:49 PM   #5
Gone Wild
 
Join Date: Apr 2014
Posts: 220
Default Re: where to land the motor leads terminals not marked

thanks I didn't see anything stamped in it I will try it! thanks scotty
cjpenny89 is offline   Reply With Quote
Unread 05-12-2016, 06:53 PM   #6
Gone Wild
Yamaha
 
Join Date: May 2012
Location: Rio Verde, Az
Posts: 2,684
Default Re: where to land the motor leads terminals not marked

Brushes are A1, A2, Magnets (coil actually) are S1, S2. There are no magnets in these motors - just electro-magnets.
Volt_Ampere is offline   Reply With Quote
Unread 05-12-2016, 08:01 PM   #7
Gone Wild
 
Join Date: Apr 2014
Posts: 220
Default Re: where to land the motor leads terminals not marked

ok I did find where they were marked I had to scrub it with some cleaner and the cleaner made it show right up.
I then tried taking the motor off and pulled the **** cover off the main shaft and windings nice right! I can not get the rest of it off the rear end. I know I can put it back together carefully just have to get the brushes depressed so the cover slides on or did I screw up the motor?
How can I get it off the rear end? I was just hoping to check to see if it was 10 spline and it was easier to swap. if I can get it off and I can put it back together I will swap the whole rear end. any ideas how to get the insides off the rear end? or just put it back together?
thanks
cjpenny89 is offline   Reply With Quote
Unread 05-12-2016, 08:13 PM   #8
Cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 64,093
Default Re: where to land the motor leads terminals not marked

You are going to drop the rear end 3-4 inches onto concrete, so the axle closest to the motor terminals hits the concrete first and the motor falls off. Trust me, this works. You may have to drop it 2 or 3 times but keep your feet clear. The motor will drop off like a boulder. I do it on the edge of the slab so the motor hits the grass not the concrete. GL
scottyb is offline   Reply With Quote
Unread 05-12-2016, 08:14 PM   #9
Gone Wild
 
Join Date: Apr 2014
Posts: 220
Default Re: where to land the motor leads terminals not marked

ok I saw this post Motor removal
I am going to try this hope I don't screw up the armature! I think I will wrap it in towels and tap it on so I don't hurt it.
cjpenny89 is offline   Reply With Quote
Unread 05-12-2016, 08:14 PM   #10
Cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 64,093
Default Re: where to land the motor leads terminals not marked

Quote:
Originally Posted by cjpenny89 View Post
ok I saw this post Motor removal
I am going to try this hope I don't screw up the armature! I think I will wrap it in towels and tap it on so I don't hurt it.
see post above
scottyb is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
Motor terminals a1 a2 s1 s2 on a series 48v ds Electric Club Car
Unmarked PDS Motor terminals Electric EZGO
motor terminals getting hot? Electric Club Car
Motor terminals Electric Club Car
Question about Motor Terminals Electric Club Car


All times are GMT -5. The time now is 04:08 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.