Motor will not slide!

george lai · 04-20-2017, 12:46 PM

Hello, can anyone tel me any tricks to getting a corroded spline to separate. I'm swapping out my bad motor for a D&D replacement. figured id ask before getting a bigger hammer. Any advice is welcome. Thanks

shaffer88 · 04-20-2017, 01:05 PM

Can you get some kroil down in there or pb blaster

george lai · 04-20-2017, 01:16 PM

Quote:

Originally Posted by shaffer88

Can you get some kroil down in there or pb blaster

working on that now. adjusting my jacking a little to give me room.

george lai · 04-20-2017, 01:58 PM

Found a weep hole at the bottom were the motor hits the gear case . just the rite place to hit the g spot with pb. and also used the same spot to pry gently.

sunoco · 04-20-2017, 02:06 PM

Did you get it off?

If not, remove the entire rear axle and tap it on the ground (on a piece of wood) with the motor pointing down. Watch your toes

whit71 · 04-20-2017, 02:10 PM

Try this, same way Sunoco is saying

http://www.buggiesgonewild.com/elect...r-removal.html

george lai · 04-20-2017, 07:27 PM

After dissecting every part off the motor I got it. I used a large grinder to put heat into the armature . The motor is bad so I just cut into it checking the temp near the spline . when it got hot to the touch , I used a small pry bar and it moved. thank god!. not as easy as the youtube video shows, lol. Thanks gents!

04-20-2017, 12:46 PM	#1
george lai Not Yet Wild Join Date: Apr 2014 Location: Western Pennsylvania Posts: 59	Motor will not slide! Hello, can anyone tel me any tricks to getting a corroded spline to separate. I'm swapping out my bad motor for a D&D replacement. figured id ask before getting a bigger hammer. Any advice is welcome. Thanks

04-20-2017, 01:05 PM	#2
shaffer88 Gone Wild Join Date: May 2013 Posts: 552	Re: Motor will not slide! Can you get some kroil down in there or pb blaster
shaffer88 Gone Wild Join Date: May 2013 Posts: 552

04-20-2017, 01:58 PM	#4
george lai Not Yet Wild Join Date: Apr 2014 Location: Western Pennsylvania Posts: 59	Re: Motor will not slide! Found a weep hole at the bottom were the motor hits the gear case . just the rite place to hit the g spot with pb. and also used the same spot to pry gently.

04-20-2017, 02:06 PM	#5
sunoco STEALTH 4X4 Join Date: Sep 2011 Location: GA Posts: 2,125	Re: Motor will not slide! Did you get it off? If not, remove the entire rear axle and tap it on the ground (on a piece of wood) with the motor pointing down. Watch your toes

04-20-2017, 02:10 PM	#6
whit71 Gone Wild Join Date: Nov 2013 Location: North Augusta SC Posts: 273	Re: Motor will not slide! Try this, same way Sunoco is saying http://www.buggiesgonewild.com/elect...r-removal.html

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

04-20-2017, 07:27 PM	#7
george lai Not Yet Wild Join Date: Apr 2014 Location: Western Pennsylvania Posts: 59	Re: Motor will not slide! After dissecting every part off the motor I got it. I used a large grinder to put heat into the armature . The motor is bad so I just cut into it checking the temp near the spline . when it got hot to the touch , I used a small pry bar and it moved. thank god!. not as easy as the youtube video shows, lol. Thanks gents!

Similar Threads
Thread	Forum
Brake slide relocate	Lifted Golf Carts
Rv slide out fix	Garage and Workshop
36 or 40 mm flat slide carb?	Big Block Talk!
Slide in hitch for Ds	Golf Carts and Parts
Motor Won't Slide Off	Electric Club Car