|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
02-15-2018, 01:38 PM | #1 |
Gone Wild
Join Date: May 2016
Posts: 225
|
regenatrive braking on 2010 model?
ser FD1055-163297 CC carry all Sepex.speed sensor seems to function fine as i get resistance and alarm when doing "push/roll cart by hand test".But when cruising down declines cart just freewheels fast with no resistance or voltage increase with go-pedal in neatral position.I have Curtis handheld IQDM (no users manual)#102248803.can i use this to reset regen braking?thanks
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-15-2018, 10:31 PM | #2 |
Gone Wild
Join Date: May 2015
Location: Houston
Posts: 903
|
Re: regenatrive braking on 2010 model?
It sounds like the regen level is turned off or way down on your cart via the controller.
|
02-20-2018, 10:40 AM | #3 |
Gone Wild
Join Date: May 2016
Posts: 225
|
Re: regenatrive braking on 2010 model?
|
02-20-2018, 11:08 AM | #4 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: regenatrive braking on 2010 model?
|
02-20-2018, 05:20 PM | #5 |
Gone Wild
Join Date: May 2016
Posts: 225
|
Re: regenatrive braking on 2010 model?
thanks Sergio,we have lots of LONG declines and hills here.would #2 setting be best as far as helping batts stay charged longer?
|
02-20-2018, 06:06 PM | #6 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: regenatrive braking on 2010 model?
Yep and it will save your brake shoes as well.
|
02-21-2018, 12:50 PM | #7 | |
Gone Wild
Join Date: May 2016
Posts: 225
|
Re: regenatrive braking on 2010 model?
Quote:
It should be in the #2 default from factory? like mentioned in earlier post,my alarm works if cart is hand pushed,so speed sensor seems OK?i am not getting any resistance on declines,if anything cart picks up speed.. |
|
02-21-2018, 02:06 PM | #8 |
Not Yet Wild
Join Date: Aug 2016
Location: Charlotte, NC
Posts: 51
|
Re: regenatrive braking on 2010 model?
Do you have speed magnet installed?
|
02-21-2018, 05:10 PM | #9 |
Gone Wild
Join Date: May 2016
Posts: 225
|
Re: regenatrive braking on 2010 model?
|
02-21-2018, 05:19 PM | #10 |
Gone Wild
Join Date: May 2016
Posts: 225
|
Re: regenatrive braking on 2010 model?
UPDATE,i was able to borrow an IQDM-P from another department.I was able to adjust Petal up mode setting to #2.So i started playing with this scanner on the fleet of carts we have to see where there settings were.why is it that i see some carts with a 4 setting for speed and when you go to adjust it,only has 1,2 and 3?of course 3 being the fastest speed..?also when i go to monitor screen the pack voltage is one full volt less then when measured with calibrated Fluke87 VOM?
|
|
|
Similar Threads | ||||
Thread | Forum | |||
EZGo TXT 2010 model jumps when start | Electric EZGO | |||
Considering 2008 or 2010 model | Electric Yamaha | |||
2010 precedent excel i2 w/excel braking | Electric Club Car | |||
2010 CC Precedent i2 Gas Model ? | Gas Club Car | |||
Speed up E-Z-GO Golfcart model 2010? | Electric EZGO |