|
|
|||||||
| Electric Club Car Electric DS, and Precedent golf cars |
  |
|
|
Thread Tools | Display Modes |
06-24-2018, 05:21 PM
|
#1 |
|
Not Yet Wild
Join Date: May 2018
Location: Augusta, GA
Posts: 57
|
Club car part number for lug stud
I purchased a stud manufactured by "Stens" that was said to fit all 82 and up Club Cars. However, I tried spinning a few of my lugs onto it and they all stop about half way. I assume the lugs should spin freely to the end of the stud.
Can anyone confirm the correct part number needed? I have a 2003 Club Car DS IQ The one I purchased was Stens 416-112 (Club Car# 103477901). Thanks! |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
06-24-2018, 05:46 PM
|
#2 |
|
Gone Wild
 Join Date: May 2015
Location: Houston
Posts: 903
|
Re: Club car part number for lug stud
Your trying to attach a the stud to the hub?
Easiest way is to use a bolt and a washer to pull the stud through the hub to set it via use of a impact wrench etc. At least I think that is what you are trying to do. |
|
|
|
|
06-24-2018, 06:13 PM
|
#3 |
|
Not Yet Wild
Join Date: May 2018
Location: Augusta, GA
Posts: 57
|
Re: Club car part number for lug stud
Sorry - that came off as a little confusing...
Background - I have a stud that broke loose whenever I was loosening a lug nut. I have yet to cut it off but figure I will destroy both the lug and the stud whenever I do. With that said, I bought a new stud and 4 new lug nuts. Both were advertised as being for Club Cars. I decided to do a test fit of the lug and stud to make sure there were no issues. I tried just holding the stud in my hand and spinning a new lug nut on, but it stops before the lug is completely on. I thought well maybe I got a bad lug, so I tried the other 3 and encountered the same thing. At this point I'm wondering if I bought the wrong stud, or maybe it's just defective. I tried cleaning/examine the threads but see no obvious issues. I'm assuming the lugs should spin freely on all the way until the end. |
|
|
|
|
06-24-2018, 06:20 PM
|
#4 |
|
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: Club car part number for lug stud
It is probably just the taper on the thread. If it made it one full nuts length on the stud, then you are fine as the TPI (threads per inch) is correct. If it did not get thru the nut/lug, then you may have a bad cut on one or the other.
|
|
|
|
|
06-24-2018, 06:53 PM
|
#5 |
|
Old Sky Soldier
Join Date: Dec 2011
Location: Kentucky
Posts: 3,881
|
Re: Club car part number for lug stud
When I had a stud spin, I drilled it out and replaced it with a stud from a cub cadet mower.
|
|
|
|
|
06-24-2018, 08:05 PM
|
#6 |
|
Cave Dweller
Join Date: Apr 2013
Location: Always On The Move
Posts: 22,239
|
Re: Club car part number for lug stud
i did one about 6 years ago and i want to say i got a stud at napa for a mid 80's mustang
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Part number | Electric EZGO | |||
| 1989 Club Car Motor terminal labels. Part number 5bc48jb771 | Electric Club Car | |||
| Wheel Stud Replacement Part Number | Electric EZGO | |||
| wheel stud part no. | Gas Club Car | |||
| part number for this??? | Big Block Talk! | |||
Linear Mode
