lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 07-19-2018, 09:36 AM   #11
Not Yet Wild
Club Car
 
Join Date: Aug 2017
Location: Martindale, TX
Posts: 49
Default Re: Motor to controller cables.

I got the new 2 gauge cables but they are still getting hot

Sent from my SM-G950U using Tapatalk
Joshaj84 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 07-19-2018, 09:50 AM   #12
Gone Wild
 
E36Racer's Avatar
Club Car
 
Join Date: Jan 2017
Location: Miami, FL
Posts: 1,024
Default Re: Motor to controller cables.

Only the motor to controller cables or the battery cables as well? Are all terminals clean and free of any corrosion? Do the cables have the correct 5/16 ring terminals? How hot are they getting? Can you touch them without burning your fingers?
E36Racer is offline   Reply With Quote
Unread 07-19-2018, 12:37 PM   #13
MOD of all BS!
 
NoleFan4Ever's Avatar
Club Car
 
Join Date: Sep 2011
Location: Florida
Posts: 9,390
Default Re: Motor to controller cables.

Yes, lets hear it or shoot it with a temp gun and tell us the degrees in F.
NoleFan4Ever is offline   Reply With Quote
Unread 07-19-2018, 01:10 PM   #14
Not Yet Wild
Club Car
 
Join Date: Aug 2017
Location: Martindale, TX
Posts: 49
Default Re: Motor to controller cables.

You can touch cables but the cart starts jerking like mcor issue when they heat up. It's the motor cables that are hottest. Nothing is corroded

Sent from my SM-G950U using Tapatalk
Joshaj84 is offline   Reply With Quote
Unread 07-19-2018, 01:26 PM   #15
MOD of all BS!
 
NoleFan4Ever's Avatar
Club Car
 
Join Date: Sep 2011
Location: Florida
Posts: 9,390
Default Re: Motor to controller cables.

What controller?
NoleFan4Ever is offline   Reply With Quote
Unread 07-19-2018, 01:48 PM   #16
Not Yet Wild
Club Car
 
Join Date: Aug 2017
Location: Martindale, TX
Posts: 49
Default Re: Motor to controller cables.

Upgraded stock 400amp upgrade


Sent from my SM-G950U using Tapatalk
Joshaj84 is offline   Reply With Quote
Unread 07-19-2018, 01:59 PM   #17
MOD of all BS!
 
NoleFan4Ever's Avatar
Club Car
 
Join Date: Sep 2011
Location: Florida
Posts: 9,390
Default Re: Motor to controller cables.

One should not be causing the other.....

Do you have a diode on the solenoid coil - if so is it oriented correctly. If you did not mess with it or replace it then no issue there.

The cables do not seem overly hot to me...

Lets make sure your MCOR is not going out. Unplug the two pin connector from the MCOR (under the floor and connected to a linkage from the pedal) and jump out the connector with a paper clip or a small piece of wire. It will be a blue wire and green wire connector. If it runs with the jumper in place, your MCOR has failed. Get one here https://www.revolutiongolfcars.com/mcors
NoleFan4Ever is offline   Reply With Quote
Unread 07-19-2018, 02:07 PM   #18
Not Yet Wild
Club Car
 
Join Date: Aug 2017
Location: Martindale, TX
Posts: 49
Default Re: Motor to controller cables.

I've tested the mcor before it tested fine. But no I don't have diobe, I bought one but the connectors on it were way too small

Sent from my SM-G950U using Tapatalk
Joshaj84 is offline   Reply With Quote
Unread 07-19-2018, 03:41 PM   #19
MOD of all BS!
 
NoleFan4Ever's Avatar
Club Car
 
Join Date: Sep 2011
Location: Florida
Posts: 9,390
Default Re: Motor to controller cables.

All I can say is there ~appears to be an MCOR or solenoid problem, unless the controller has an issue.

And remember, the MCOR is two part; micro-switch AND potentiometer.

Double check all your cabling for a lose connection or a faulty terminal or lug.
NoleFan4Ever is offline   Reply With Quote
Unread 07-19-2018, 07:53 PM   #20
Gone Wild
 
WalterM6's Avatar
Club Car
 
Join Date: Apr 2017
Posts: 900
Default Re: Motor to controller cables.

Which motor cables are heating up? What motor and controller combination do you have? Could be your overdriving your motor and it is heating them up.
WalterM6 is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
2010 Club car new D&D motor controller solenoid cables Electric Club Car
Upgrading controller, motor, solenoid, f/r, and all cables. How hard is it? Electric EZGO
4g battery cables with 2g motor cables Electric EZGO
1/0 Battery Cables to 6 AWG Motor Cables Electric EZGO
2ga Motor & Controller Cables (Alone) Electric EZGO


All times are GMT -5. The time now is 10:32 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.