lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 11-01-2018, 11:11 AM   #1
Not Yet Wild
 
Join Date: Oct 2018
Posts: 23
Default What kind of adhesive? OEM Seat

My CC Precedent project has a stock seat that has come off of the plastic back piece. Overall the seat vinly, cushion and back piece are in fine shape. Just need to glue it back in place.

NOTE: This is a bit tricky for the following reasons. Vinly shrinks with temperature. So the cushion is smaller than the plastic. I can use a heat gun to soften it up but I need an adhesive that will bond and hold fairly quickly, while I soften up the next area and work my way around until its repaired.

Any suggestions on what adhesive to use ? Or just thoughts in general.
CoolHanMatt is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 11-02-2018, 01:59 PM   #2
Not Yet Wild
 
Join Date: Oct 2018
Posts: 23
Default Re: What kind of adhesive? OEM Seat

Bump
CoolHanMatt is offline   Reply With Quote
Unread 11-02-2018, 02:36 PM   #3
MOD of all BS!
 
NoleFan4Ever's Avatar
Club Car
 
Join Date: Sep 2011
Location: Florida
Posts: 11,543
Default Re: What kind of adhesive? OEM Seat

I have always used 3M Scotch-Weld. It is a Nitrile HP rubber adhesive that permanently bonds leather, rubber, vinyl, etc. I apply it to both sides and let it set a minute or two and then I stick it together and hold it or tape it down for a few hours. It will set fairly quickly, but will not completely harden for several hours.
NoleFan4Ever is offline   Reply With Quote
Unread 11-02-2018, 03:54 PM   #4
Gone Wild
 
PingEye3's Avatar
Club Car
 
Join Date: Sep 2014
Location: Orlando, FL
Posts: 735
Default Re: What kind of adhesive? OEM Seat

My seat back came apart like that when I first got the cart in 2013. I used contact cement to glue the back to the backplate. Then, because the cushion has shrunk like you described, I picked up some 1/2" nylon rope from Ace and used my glue gun to glue it in place. You start at the bottom middle and glue the end in place. You will add glue and press it down to fill the gap and go all the way around the seat back. See picture. It is not a great pic but you can see it. I have done this for several members with seats like that at the club. It works on the bottom cushion as well. Three of these repairs are 3 yrs old and still holding well and one of them is a maintenance cart at the club.
Attached Images
File Type: jpg Rope CC seat repair.jpg (325.6 KB, 0 views)
PingEye3 is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
What kind of rear seat do I have? Electric Club Car
polypropalene adhesive/filler Gas Yamaha
Windshield Adhesive Electric Club Car
? About adhesive promotor! Electric EZGO
vinyl seat adhesive needed. Gas EZGO


All times are GMT -5. The time now is 12:54 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.