|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
08-10-2019, 06:44 PM | #1 |
Gone Wild
Join Date: Dec 2011
Posts: 168
|
What is this solenoid and do I need it?
2013 carryall 6 which I think is similar to a precedent. Not sure of a good way to post pics here yet. It's a large, like 3"X4", square solenoid under the seat on the passenger side mounted against the back "wall." It had a rusty blade which broke off on the coil connection I assume. I have not found any changes with the cart yet except now I know what seemed to be clicking every 30-90 sec or something. I have a 2011 parts manual and it just says "102774701 Solenoid, 48V" and appears to be connected to a motor controller which must be on the other side of the wall or box.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-10-2019, 09:52 PM | #2 |
Gone Wild
Join Date: Jan 2017
Location: Queensland Australia
Posts: 1,332
|
Re: What is this solenoid and do I need it?
It sounds like the OBC, the solenoid attaches near it (see the attachments).
|
08-11-2019, 12:13 AM | #3 | |
Gone Wild
Join Date: Dec 2011
Posts: 168
|
Re: What is this solenoid and do I need it?
Quote:
edit: my set up is different than that but that's what the solenoid looks like |
|
08-11-2019, 12:25 AM | #4 |
Gone Wild
Join Date: Dec 2011
Posts: 168
|
Re: What is this solenoid and do I need it?
Maybe it's normal closed and it needs to activate and disconnect for the tow/run switch or something? I'd guess it switches entire pack power for something since it's so big and is switching #2 cables.
I guess I could check to see if it's open or closed. |
08-11-2019, 01:30 AM | #5 |
Gone Wild
Join Date: Dec 2011
Posts: 168
|
Re: What is this solenoid and do I need it?
Now wait a minute! I got it screwed up. I guess maybe because of bad light and looking at pics or something but NOOOO, it's like 2"X 3" and only switches a wire which looks to be about 14 gauge. SORRY ABOUT THAT! I might have that part number wrong too. I don't think there is a solenoid which switches 14 gauge wire in my parts manual.
For what it's worth, right now while on the charger it reads 58 V with the negative meter lead on one side and the positive lead to positive on the pack and nothing on the other cable connection, so it must switch a negative and is normally open? edit- later found the charge did go to completion and seemed normal. I wonder though if the OBC uses that solenoid to sample the pack and "adjust." I thought this charger and algorithm only went to 55.3 but that's in the bulk phase and I never checked it at a random point in the final phase where I saw 58V here. I expected it to be lower in the final phase. I wonder if because that solenoid is disconnected, and if the OBC is not able to monitor because of it, then maybe it charged with a default or something? It would be nice to leave that solenoid disconnected so I don't have to hear that clicking all the time but would it ruin something? I wanted to fix the thread after finding I screwed up ID'ing this thing but I guess I can't delete my posts ? Last edited by alchemy; 08-11-2019 at 03:31 AM.. Reason: typo |
08-11-2019, 01:43 AM | #6 |
Gone Wild
Join Date: Dec 2011
Posts: 168
|
Re: What is this solenoid and do I need it?
yawood your pic could still be right and the solenoid does look like that just smaller than I originally thought. The pic in my parts manual and others for the part number I posted look to be for #2 cable and not the one I broke the blade off of.
|
08-11-2019, 05:23 AM | #7 |
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: What is this solenoid and do I need it?
alchemy, can you post a photo of what you are talking about?
|
08-11-2019, 01:13 PM | #8 |
Gone Wild
Join Date: Dec 2011
Posts: 168
|
Re: What is this solenoid and do I need it?
finally figured how to load pics
the bar code looks like it says something like SOL2112 |
08-11-2019, 02:27 PM | #9 |
Gone Wild
Join Date: Dec 2011
Posts: 168
|
Re: What is this solenoid and do I need it?
here is from a 2011 carryall 6 (mine's a 2013) parts manual for the "solenoid 48V 102774701 "
Although it looks the same I don't think that's it as you can see the heavy cables and other components. The one I'm speaking of in the pic only has small wire with no such components visible near by. It's under the passenger side seat against a wall by itself. I'm wondering if parts sites are mixing it up too. I'd guess I probably do have this solenoid in the diagram inside the aluminum box or behind that wall as well. OR, maybe they rigged it to use differently for something and put it on the outside of the box with smaller wires?? Pretty sure though that only a golf car dealership ever worked on this. |
08-11-2019, 04:02 PM | #10 |
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: What is this solenoid and do I need it?
I'm not sure what that little solenoid with those small wires goes to. You will need the exact wiring diagram for your cart.
If the cart is operating normally and there is no solenoid click you have another issue or it could be related. IDK what that little solenoid does. |
|
|
Similar Threads | ||||
Thread | Forum | |||
1989 Club Car DS 36v -New Vglide/Solenoid/microswitches Only moves when solenoid jump | Electric Club Car | |||
Wrong Solenoid in my cart? w/ Pics- Please suggest correct solenoid I should be using | Electric EZGO | |||
96 club car ds solenoid wont click and cart wont move unless you jump solenoid | Electric Club Car | |||
Solenoid not engaging with Forward / Reverse switch? (Solenoid is good) | Electric EZGO | |||
Help converting G1 solenoid setup to single G16 solenoid | Gas Yamaha |