need advice on obc

toogood4ubalius79 · 08-13-2010, 11:26 PM

To all who can help i have a 95 cc 48 volts with six 8 volt trojans t 890 s upgraded to d d torque motor for hunting in the hills and my obc went out i am done for the night working on it, but my question is my new obc is the same but i got a fuse kit in the box and do i need to put it on its a little different looking with a silver billet shaped end on it and i dont recall mine begin like that but have not got there yet,, next question is my obc that i took out had a 4 guage cable going to batt. 6 and the new obc came with 6 gauge will i lose any at all torque with that or is it just to tell the charge of pack.. next the kit came with a battery warning light and my cart

dont have that do i need to put it in or can i use without perferably without if possibe i read in the instruction that it need to be on so it will work correctly but it said things about different years thank man in advance i want to finish in the morning i got obc mounted up and wires hooked to controller and called it a night

Mark 525 · 08-13-2010, 11:38 PM

hello all i have aproblem i bought new batteries for my 36 volt cart and the charger will not charge the batteeries can u help

toogood4ubalius79 · 08-13-2010, 11:53 PM

u need to start a new thread go to bottom of main page and hit the new thread tab welcome to BBG main page under club cart at bottom but i will try to help get thread started and other will help too

Fishing Dude · 08-14-2010, 04:03 AM

You do need the light from what I understand. The one wire is with the silver thing is for the grey wire, the fuse goes on red wire to the solenoid. The light is for diagnostic use at the dealer also. Yes you need to change the 6 ga wire to 4 ga but could just run both adding the 4 ga running around your obc.

toogood4ubalius79 · 08-14-2010, 08:51 AM

fishing dude you talking about running two wires off last neg.. of pack one going threw the obc to the controller B spot and the other around to the B spot as well

scottyb · 08-14-2010, 08:57 AM

Yes 2 cables. Actually two #6 will do the job of a #4 just fine. I have done many without the extra fuse kit installed but, I recommend the warning light be installed in the dash.

toogood4ubalius79 · 08-14-2010, 09:01 AM

so you think scotty that i can get by without putting in fuse pin in charger port.... so i hook the warning light up to key switch. i hope the cart has the right hook up wires because it doesnt have a warning light on it when i bought it thanks in advance

rib33024 · 08-14-2010, 09:04 AM

Quote:

Originally Posted by toogood4ubalius79

fishing dude you talking about running two wires off last neg.. of pack one going threw the obc to the controller B spot and the other around to the B spot as well

Yes he is,. --

toogood4ubalius79 · 08-14-2010, 09:05 AM

Scotty is it worth the trouble to cut the end and change to #4 if i dont change it i will see a power loss... what u mean use 2 #6

toogood4ubalius79 · 08-14-2010, 09:08 AM

Thanks so there will be the 10 guage from the obc and a 6 gauge and another smaller wire i dont know what it is and my 4 gauge wire all on the Controller B tab correct

08-13-2010, 11:26 PM	#1
toogood4ubalius79 Gone Wild Join Date: Feb 2009 Location: mississippi Posts: 213	need advice on obc To all who can help i have a 95 cc 48 volts with six 8 volt trojans t 890 s upgraded to d d torque motor for hunting in the hills and my obc went out i am done for the night working on it, but my question is my new obc is the same but i got a fuse kit in the box and do i need to put it on its a little different looking with a silver billet shaped end on it and i dont recall mine begin like that but have not got there yet,, next question is my obc that i took out had a 4 guage cable going to batt. 6 and the new obc came with 6 gauge will i lose any at all torque with that or is it just to tell the charge of pack.. next the kit came with a battery warning light and my cart dont have that do i need to put it in or can i use without perferably without if possibe i read in the instruction that it need to be on so it will work correctly but it said things about different years thank man in advance i want to finish in the morning i got obc mounted up and wires hooked to controller and called it a night

08-13-2010, 11:38 PM	#2
Mark 525 Not Yet Wild Join Date: Aug 2010 Posts: 2	Re: need advice on obc hello all i have aproblem i bought new batteries for my 36 volt cart and the charger will not charge the batteeries can u help
Mark 525 Not Yet Wild Join Date: Aug 2010 Posts: 2

08-13-2010, 11:53 PM	#3
toogood4ubalius79 Gone Wild Join Date: Feb 2009 Location: mississippi Posts: 213	Re: need advice on obc u need to start a new thread go to bottom of main page and hit the new thread tab welcome to BBG main page under club cart at bottom but i will try to help get thread started and other will help too

08-14-2010, 08:51 AM	#5
toogood4ubalius79 Gone Wild Join Date: Feb 2009 Location: mississippi Posts: 213	Re: need advice on obc fishing dude you talking about running two wires off last neg.. of pack one going threw the obc to the controller B spot and the other around to the B spot as well

08-14-2010, 09:01 AM	#7
toogood4ubalius79 Gone Wild Join Date: Feb 2009 Location: mississippi Posts: 213	Re: need advice on obc so you think scotty that i can get by without putting in fuse pin in charger port.... so i hook the warning light up to key switch. i hope the cart has the right hook up wires because it doesnt have a warning light on it when i bought it thanks in advance

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

08-14-2010, 04:03 AM	#4
Fishing Dude Gone Wild Join Date: Jul 2008 Location: Slums of Lake Erie Posts: 3,721	Re: need advice on obc You do need the light from what I understand. The one wire is with the silver thing is for the grey wire, the fuse goes on red wire to the solenoid. The light is for diagnostic use at the dealer also. Yes you need to change the 6 ga wire to 4 ga but could just run both adding the 4 ga running around your obc.

08-14-2010, 08:57 AM	#6
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,410	Re: need advice on obc Yes 2 cables. Actually two #6 will do the job of a #4 just fine. I have done many without the extra fuse kit installed but, I recommend the warning light be installed in the dash.

08-14-2010, 09:05 AM	#9
toogood4ubalius79 Gone Wild Join Date: Feb 2009 Location: mississippi Posts: 213	Re: need advice on obc Scotty is it worth the trouble to cut the end and change to #4 if i dont change it i will see a power loss... what u mean use 2 #6

08-14-2010, 09:08 AM	#10
toogood4ubalius79 Gone Wild Join Date: Feb 2009 Location: mississippi Posts: 213	Re: need advice on obc Thanks so there will be the 10 guage from the obc and a 6 gauge and another smaller wire i dont know what it is and my 4 gauge wire all on the Controller B tab correct

Similar Threads
Thread	Forum
Any advice	Electric EZGO
need advice	Gas Club Car
Need advice...	Electric Club Car
Advice on G22	Gas Yamaha
Advice	Gas EZGO