![]() |
|
Electric Club Car Electric DS, and Precedent golf cars |
![]() ![]() |
Thread Tools | Display Modes |
![]() | #1 |
Not Yet Wild Join Date: Sep 2010
Posts: 61
| ![]() Once again I have questions after reading some of the posts about controllers overheating. I am putting a 700 logistics controller, w/ a GE 380 motor, running 48volts in my ezgo. This cart will be used to cruise around neighborhood in the summer and at deer lease in the fall. I do not want a lead sled, but alittle speed would be nice. I will have upgraded the cables. so So will have a prob w overheating the controller????????? thx |
![]() | ![]() |
![]() | |
![]() __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum | |
![]() | #2 |
Gone Wild ![]() Join Date: Mar 2009 Location: South Texas
Posts: 2,391
| ![]() To be on safe side I would contact Logistics people with all info of motor HP, Cable size, cart extra's like lift, tire size, etc for correct answer, better safe than sorry. Anyone can make a guess but parts maker is last word on what will and will not work, besides they are the ones to replace in case of defects. |
![]() | ![]() |
![]() | #3 |
Not Yet Wild Join Date: Sep 2010
Posts: 61
| ![]() Does anyone have the contact info. for logistics. thx la-boy |
![]() | ![]() |
![]() | #4 |
Gone Wild ![]() Join Date: Mar 2009 Location: South Texas
Posts: 2,391
| ![]() I had neighbor purchase a Logisystem Controller from Grass Roots Electrical Vehicles and he gave me following site for Logisystems www.logisystemscontroller.com |
![]() | ![]() |
![]() | #5 |
Not Yet Wild Join Date: Sep 2010
Posts: 61
| ![]() The site says it is under const.??? oh well, I'll check back later. Btw I am prob. putting some 23" off road tires with a 5" lift also, that might help the controller work better, they say its for speed and torque when ran with the GE 380. If anyone has this simlilar set-up, could you tell me what is the aprox. run time on the batts. thx. again |
![]() | ![]() |
![]() | #6 |
Gone Wild ![]() Join Date: Mar 2009 Location: South Texas
Posts: 2,391
| ![]() Any time you change tire diameter and add lifts, tops, windshields, climbing hills, rear seats, etc, you are putting more load on cart to get up to speed and THIS IS REASON for higher amp controllers so you dont have a melt down of controller and or motor. Heat is what ruins motors and controllers, F&R controls, 6 guage wiring, etc. Once you are able to get up to speed then larger tire diameter will allow you to go faster. |
![]() | ![]() |
![]() | #7 |
Not Yet Wild Join Date: Sep 2010
Posts: 61
| ![]() I had just heard that running a larger controller at slow speeds might overheat it. |
![]() | ![]() |
![]() | #8 |
Master BS'r ![]() ![]() Join Date: Jul 2007 Location: S. Florida
Posts: 1,819
| ![]() I run this set up on my 95CCDS48 volt, my cart is lifted with 23", backseat, mud tires. The controller will heat up and shut down on extended rides or too much weight, so be carefull. The thermal shut down feature has saved my but a few times...give it a few minutes to cool down...then go home easy. I've also, shut it down pulling 2-300lb bulders, kind of stupid..I know, but it was the only way to get them moved at the time. That is a great motor, and for the price a great controller. There are better setups, imop, a d-390, same controller, regeared, same volts will yeild as fast a cart with more torque. My 1/2 cent. BTW, that will be my next set up or 64 volts! |
![]() | ![]() |
![]() | #9 |
Gone Wild ![]() Join Date: Mar 2009 Location: South Texas
Posts: 2,391
| ![]() LA-BOY-- Low speed is not a problem ( that I am aware of ) because unless you are trying to climb a tree or push a wall over or locked up brakes at light pedal push there is less chance of heat build up with larger solid state controller. If you have a resistor coil cart then heat builds up more at slow speed because more coils are passing power through them? |
![]() | ![]() |
![]() | #10 |
Not Yet Wild Join Date: Sep 2010
Posts: 61
| ![]() Thx for all the info. I finished the rear end swap w/the 5" lift and will start on the front tomorrow. The shocks do not reach the new lift plates, is that gonna be a issue. Also, the clubcar rearend w/the motor shows the bottom 2 motor lugs pointing at a angle down. Is that the way they are supposed to look. It is the only way they can, so I am probablt answering my own question.....I also OSPHOed the batt. tray and red oxided it. It's coming along but still a long way to go.........need a cheap set of 10" steel wheels, any sugg............. |
![]() | ![]() |
![]() |
|
Thread Tools | |
Display Modes | |
|
![]() | ||||
Thread | Forum | |||
Club car DS or EZ go for 1000cc build | Bike & ATV Engine Swaps | |||
Club Car Build | Big Block Talk! | |||
2000 gas club car build | Members Rides | |||
club car rear coil over build | Lifted Golf Carts | |||
club carnew build 2008 | Lifted Golf Carts |