|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
04-12-2011, 05:10 PM | #1 |
Not Yet Wild
Join Date: Feb 2011
Location: dublin ^.^
Posts: 35
|
how to dummy signals from OBC???
does anyone know how to dummy the signals from/to the OBC?
also, if your looking for the pinout for the 1510 controller (colour coded) and what each signal is pm me or email me and ill send em onto you. got them from club car :) but it doesnt seem to tell me exactly what the OBC is doing. ty again peeps :) |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-12-2011, 05:55 PM | #2 |
The Last Moja Morani
Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: how to dummy signals from OBC???
the OBC controls charging as for dumming it i don,t know that you can......you can dummy the charger but other than a very basic 95-96 where you can bypass the OBC never heard of anything else.................
|
04-12-2011, 06:28 PM | #3 |
Not Yet Wild
Join Date: Feb 2011
Location: dublin ^.^
Posts: 35
|
Re: how to dummy signals from OBC???
yeah and can lock you out if a problem is detected which is what i think is happening as 2 controllers = no movement and everything else seems fine.
if i knew what the 6 wires sent when everything is ok i can dummy them, just need to know the voltage levels on each wire when everything is fine then i can get rid of obc :P |
04-12-2011, 07:26 PM | #4 |
Not Yet Wild
Join Date: Sep 2010
Location: South Louisiana
Posts: 21
|
Re: how to dummy signals from OBC???
I am not claiming the following, it was posted somewhere on this site and i saved it for future reference:
OBC WIRES function explained Red(18-gauge) Main power supply for the onboard computer. The vehicle batteries provide +48 volts to the onboard computer. White (18-gauge) The Tow/Run switch provides +48 volts to the OBC through the white wire when the switch is in the RUN position. When the Tow/Run switch is in the TOW position, the OBC locks out the speed controller by not sending a +48 volt signal through the light blue OBC wire. Yellow (18-gauge) Enables the OBC to power-up (brings the OBC out of sleep mode) when the accelerator pedal is pressed. The MCOR limit switch provides +48 volts to the OBC when the accelerator pedal is pressed. Brown/White (18-gauge) Controls the battery warning light by providing a ground to the light through a transistor inside the OBC. Light Blue (18-gauge) Solenoid lockout circuit – the OBC provides a +48 volt signal to the speed controller when the battery charger is disconnected. Green/White (18-gauge) Reserved for future use. Wire serves no function at this time Gray (18-gauge) Provides a ground for the charger relay when the battery charger is connected to the vehicle. Also enables the OBC to power-up (brings the OBC out of sleep mode). Black (10-gauge) to battery charger receptacle Battery charging current is controlled by the SCR (siliconcontrolled rec Black (10-gauge) to B– terminal of speed controller tifier) inside the onboard computer. Black (6-gauge) through onboard computer Allows the hall-effect sensor inside the OBC to measure the amount of current passing through this wire. |
04-12-2011, 07:47 PM | #5 |
Not Yet Wild
Join Date: Feb 2011
Location: dublin ^.^
Posts: 35
|
Re: how to dummy signals from OBC???
tyvm this has shed light on the little 'black' box.
will check out tomorrow and get back to you, cheers m8 :) |
04-13-2011, 07:47 AM | #6 | |
The Last Moja Morani
Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: how to dummy signals from OBC???
Quote:
this is worth being a sticky if it isn,t........................ |
|
04-13-2011, 08:27 AM | #7 |
Not Yet Wild
Join Date: Feb 2011
Location: dublin ^.^
Posts: 35
|
Re: how to dummy signals from OBC???
defo worth a sticky ^.^
|
04-13-2011, 06:25 PM | #8 |
Not Yet Wild
Join Date: Sep 2010
Location: South Louisiana
Posts: 21
|
Re: how to dummy signals from OBC???
Feel free to put the glue to it then!
Seems like it was part of an extremely detailed and lengthy posting by a retired electrical engineer, Wish i could be more exact. |
04-13-2011, 06:30 PM | #9 | ||
......................
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
Re: how to dummy signals from OBC???
Quote:
This is where I found it Quote:
|
||
04-13-2011, 06:37 PM | #10 |
Not Yet Wild
Join Date: Sep 2010
Location: South Louisiana
Posts: 21
|
Re: how to dummy signals from OBC???
Thats it!
In a long trail by Dr, Bob title was "How does 48V 2001 Club Cart OBC function?" |
Tags |
obc |
|
|
Similar Threads | ||||
Thread | Forum | |||
Turn signals | Electric Club Car | |||
turn signals | Electric Club Car | |||
Turn signals | Electric EZGO | |||
2001 CC Battery Dummy Light (trigger?) | Electric Club Car | |||
Turn Signals | Electric Club Car |