|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
06-01-2011, 09:56 AM | #1 |
72 volt torque monster
Join Date: Dec 2009
Location: Sorrento, FLA
Posts: 589
|
anyone make a 9-1 or 10-1 rear gear?
Just what the title says?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-01-2011, 11:35 AM | #2 |
Gone Wild
Join Date: Mar 2009
Location: Roseville, CA
Posts: 2,757
|
Re: anyone make a 9-1 or 10-1 rear gear?
8:1, 6:1 and 15:1 are readily available.
Some of the import carts like Star and Zone came stock with a 10.25:1 and may fit. |
06-01-2011, 11:44 AM | #3 |
72 volt torque monster
Join Date: Dec 2009
Location: Sorrento, FLA
Posts: 589
|
Re: anyone make a 9-1 or 10-1 rear gear?
cool, I am not even sure what rear end I have in my 02 cc. 9-1 would be perfect if I could find it.
|
06-01-2011, 11:49 AM | #4 |
Gone Wild
Join Date: Mar 2009
Location: Roseville, CA
Posts: 2,757
|
Re: anyone make a 9-1 or 10-1 rear gear?
Use an 8:1 and reduce your tire size by 2" diameter and you will have the same result as a 9:1.
|
06-01-2011, 12:04 PM | #5 |
72 volt torque monster
Join Date: Dec 2009
Location: Sorrento, FLA
Posts: 589
|
Re: anyone make a 9-1 or 10-1 rear gear?
looking at the rear end, I think I have a graziano, it has 3/4" fill and drain plugs, and the bolts to the housing come out the passenger side.
I have 23" tires now, so what is my "actual" gear now with the stock 12.44-1? |
06-01-2011, 12:22 PM | #6 |
72 volt torque monster
Join Date: Dec 2009
Location: Sorrento, FLA
Posts: 589
|
Re: anyone make a 9-1 or 10-1 rear gear?
Looking online at the calculaters for rear gear, need to know what the rpm is of the motor, would 3800 be about right for the plum quick purple motor?
|
06-01-2011, 01:37 PM | #7 |
Gone Wild
Join Date: Mar 2009
Location: Roseville, CA
Posts: 2,757
|
Re: anyone make a 9-1 or 10-1 rear gear?
A PQ motor could be wound to anything.
Rpm is based on the voltage applied and the ability of the controller and cabling to get the motor up to speed. You are also limited by the HP of the motor. Check with PQ to see what motor you have and the specs is was rewound to, it could be anywhere between 2500 and 6000 rpm. |
06-01-2011, 10:41 PM | #8 |
revolutiongolfcars.com
Join Date: Mar 2010
Location: Golf Car Capital of The World... Augusta, Georgia
Posts: 10,224
|
Re: anyone make a 9-1 or 10-1 rear gear?
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
is it possible to make posi rear end? | Gas EZGO | |||
need rear end gear | Melex | |||
Bad rear end E Z Go 3 wheel make grinding sound | Electric golf carts | |||
Anybody make a rear seat for a G1 ? | Gas Yamaha |