|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
08-01-2011, 06:32 PM | #1 |
Mr. Helper
Join Date: May 2009
Location: NY Catskills & South carolina
Posts: 445
|
Will #2 cables pass thru the obc
does anyone know if #2 wires will pass thru the opening on the on-board computor ( 2005 club car )
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-01-2011, 07:04 PM | #2 |
The Last Moja Morani
Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: Will #2 cables pass thru the obc
just barely but without the end on..................................
|
08-01-2011, 07:09 PM | #3 | |
Ban Puppy Mills & Stores!
Join Date: Dec 2008
Location: SE Florida
Posts: 2,955
|
Re: Will #2 cables pass thru the obc
Quote:
Don't have the thread but they actually found some solid copper, threaded it and used it instead of the SS shown below! Take a 3" length of 5/16 threaded stainless steel. Wrap a 1/2" thick piece of insulator tape in the center. Stack yourself 2 x 1 1/2" neoprene 5/16 washers, 2 x 1" 5/16 plastic washers. One on each side of the tape gap. Then stainless washer and nut on either side to snug the shaft up in the hole. Then the stainless washers and nuts to make battery posts on either side after the first set of washers and nuts. 3" works depending on the thickness of your washers. Be careful not to overtighten the nuts after placing stack through the hole and you obviously have to hold the first set of nuts with a wrench when tightening the final nuts. Now you essentially have battery posts on either side of the OBC and you can do whatever thickness of cable you want. It looks like CC made it that way. I used 4 gage I had custom made by a guy on eBay. They were beautiful. You can have them color coded to the stock cables. Coat everything in dielectric grease. |
|
08-01-2011, 07:30 PM | #4 |
The Last Moja Morani
Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: Will #2 cables pass thru the obc
sb, i have passed thur 2 gage cable on a few differnt occasions.......tight fit but it goes.......never left in in there but did get it thur.......just barely.................
|
08-01-2011, 07:36 PM | #5 | |
Ban Puppy Mills & Stores!
Join Date: Dec 2008
Location: SE Florida
Posts: 2,955
|
Re: Will #2 cables pass thru the obc
Quote:
My #4 took forever to pass through my OBC... super tight fit. Then again maybe older model OBC's have bigger holes... |
|
08-01-2011, 09:37 PM | #6 |
72 volt torque monster
Join Date: Dec 2009
Location: Sorrento, FLA
Posts: 589
|
Re: Will #2 cables pass thru the obc
Yall should use the search feature here,should find some interesting results.
|
08-02-2011, 06:35 AM | #7 |
Medicare Recipient
Join Date: Jun 2011
Location: West Michigan
Posts: 3,541
|
Re: Will #2 cables pass thru the obc
|
08-02-2011, 07:46 AM | #8 |
The Last Moja Morani
Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: Will #2 cables pass thru the obc
yeah SB i think the 1st gen. OBC,s may have been a hair bigger can,t confirm but like i said i was just seeing if it would fit thur.......................
|
08-02-2011, 08:01 AM | #9 |
Ban Puppy Mills & Stores!
Join Date: Dec 2008
Location: SE Florida
Posts: 2,955
|
Re: Will #2 cables pass thru the obc
|
08-02-2011, 08:32 AM | #10 |
Getting Wild
Join Date: May 2009
Location: South Carolina
Posts: 137
|
Re: Will #2 cables pass thru the obc
I got 2 gauge thru an obc on an 06 precedent with a little lube and it went right in.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Flash to pass? | Tomberlin | |||
what will changing my cables to 4g welding cables do to my performance exactly | Electric EZGO | |||
Gas Yamaha G1 oil by-pass | Gas Yamaha | |||
need more power 2002 ez go 6 pass | Gas EZGO | |||
Wanted: EZGO 6 Pass. Limo f/r cables | Golf Carts and Parts |