|
|
|||||||
| Electric Club Car Electric DS, and Precedent golf cars |
  |
|
|
Thread Tools | Display Modes |
06-06-2008, 10:23 PM
|
#1 |
|
Gone Wild
 Join Date: Oct 2007
Location: Snellville, Ga.
Posts: 1,304
|
welding gears for posi unit
I have seen a post somewhere on how to do this but cannot find any where. Does anyone else have a link to it. Suppose to do same thing as BU kit but much cheaper and stronger. Thanks, Mike
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
06-06-2008, 10:57 PM
|
#2 |
|
Totally Bonkers!
Join Date: Feb 2008
Location: Full time RVing
Posts: 1,897
|
Re: welding gears for posi unit
Well i don't know about welding golf cart rer ends but I know how I welded my race car rear ends and it should be similar.
|
|
|
|
|
06-06-2008, 10:57 PM
|
#3 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: welding gears for posi unit
MIke i had asked a question about this and we did get some good directions finally on what welds to what....
First the disclaimer. LMAO  http://www.buggiesgonewild.com/desig...ng-diff-2.html |
|
|
|
|
06-06-2008, 11:06 PM
|
#4 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: welding gears for posi unit
And here is the thread where we got the Diagrams of what to weld to what !
http://www.buggiesgonewild.com/gas-c...-system-2.html |
|
|
|
|
06-06-2008, 11:59 PM
|
#5 |
|
Gone Wild
Join Date: Mar 2008
Posts: 291
|
Re: welding gears for posi unit
make it look like this, this is from my club car.. i have had no problems since...
 |
|
|
|
|
06-07-2008, 12:17 AM
|
#6 |
|
Gone Wild
Join Date: Oct 2007
Location: Snellville, Ga.
Posts: 1,304
|
Re: welding gears for posi unit
Thanks
|
|
|
|
|
06-07-2008, 01:30 AM
|
#7 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: welding gears for posi unit
Thanks John.
 |
|
|
|
|
06-07-2008, 07:05 AM
|
#8 |
|
Gone Wild
Join Date: May 2008
Posts: 772
|
Re: welding gears for posi unit
Sounds like a good old lincoln locker!!
|
|
|
|
|
06-07-2008, 11:53 AM
|
#9 |
|
Gone Wild
Join Date: Mar 2008
Posts: 291
|
Re: welding gears for posi unit
yup, seems to work very well, but make sure to weld them solid, or they will let go and shatter the carrier, trust me i speak from expierience!! use a good torch and get it nice and warm before welding, seems to make nicer welds cause of the cast.. good luck!!
|
|
|
|
|
08-02-2008, 08:56 AM
|
#10 |
|
Getting Wild
Join Date: Dec 2007
Posts: 79
|
Re: welding gears for posi unit
I would think twice about permently welding the rear together. Not sure if your aware but it will make the front push more and turn less. I tried this on my EZGO and was not happy with it. My latest cart is a Club Car so i decided to use the Intellilock in the rear end. Drives much better and locks up solid very quickly when required.
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| E 29 rear end welding spider gears 4 posi | Gas EZGO | |||
| Welding Helmets | Garage and Workshop | |||
| Welding the diff | Design Center | |||
| welding cart | Golf Carts and Parts | |||
Linear Mode
