lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 02-19-2007, 03:12 PM   #1
Gone Wild
 
tungpo1's Avatar
E-Z-GO
 
Join Date: Dec 2006
Location: St. Johns /Jacksonville
Posts: 2,383
Default 1989 36v resistor club car

Doing a brake job for this customer when I noticed the rear lift that concerned me a little.But oh my god look what he did for the front lift, he cut the frame and !! well just take a look LOL!!!!!




tungpo1 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 02-19-2007, 04:08 PM   #2
Gone Wild
 
Join Date: Dec 2006
Location: ComplainAboutNoNo'sProfile-Ville
Posts: 4,995
Default

SWEET FANCY MOSES! No thanks, my frame strength is still intact with my spindle lift. :)
NO NO NO E-Z-GO! is offline   Reply With Quote
Unread 02-19-2007, 04:13 PM   #3
Are You Ready???
 
spriddle's Avatar
Yamaha
 
Join Date: Dec 2006
Location: middle TN
Posts: 23,523
Default

Humm..........homemade Z lift. I do like the hose clamps on the rear leafs.

spriddle is offline   Reply With Quote
Unread 02-19-2007, 04:17 PM   #4
Gone Wild
 
tungpo1's Avatar
E-Z-GO
 
Join Date: Dec 2006
Location: St. Johns /Jacksonville
Posts: 2,383
Default

Oh yes a fine job!!! it ride like its going to fall apart
tungpo1 is offline   Reply With Quote
Unread 02-19-2007, 04:19 PM   #5
Are You Ready???
 
spriddle's Avatar
Yamaha
 
Join Date: Dec 2006
Location: middle TN
Posts: 23,523
Default

I would be scared to turn the wheel. Dang! How wobbly was the front end? And are the hose clamps the only thing keeping that block from sliding back and forth: besides the one u-bolt? Does the backend even flex at all?

spriddle is offline   Reply With Quote
Unread 02-19-2007, 04:55 PM   #6
Gone Wild
 
tungpo1's Avatar
E-Z-GO
 
Join Date: Dec 2006
Location: St. Johns /Jacksonville
Posts: 2,383
Default

it does have a piece of all thread through the square tube my man I have to talk to this guy, its bad..
tungpo1 is offline   Reply With Quote
Unread 02-19-2007, 08:03 PM   #7
Gone Wild
 
IAMCOOL's Avatar
 
Join Date: Dec 2006
Posts: 181
Default

well the rear is bads but the front is a z lift... although it isnt slanted forward slightly to allow for the tie rod to move properly z lifts are alot stronger than spindle lifts and add strenth to that section of the frame ... not decrease it...not just my opinion... these are facts....but yes the back is bad....just cut a u notch in the square tubing and it will be fine
IAMCOOL is offline   Reply With Quote
Unread 02-19-2007, 08:12 PM   #8
Are You Ready???
 
spriddle's Avatar
Yamaha
 
Join Date: Dec 2006
Location: middle TN
Posts: 23,523
Default

I have heard that the Z lifts are very strong. It looks like the strength would be weakened a little in the side to side area since your loosing the I beam configuration and also dropping about 6 inches on the front. I'm just thinking out loud here and stating an opinion for discussion.

spriddle is offline   Reply With Quote
Unread 02-19-2007, 10:54 PM   #9
Gone Wild
 
4vertical's Avatar
Club Car
 
Join Date: Jan 2007
Location: La Porte Indiana
Posts: 1,388
Default

how thick are the plates that were used? the sparkie that I had had a z lift. I beat the heck out of it without problems. that rear though...

BTW I am sure your customer appreciates you splashing hiis lack of knowledge all over the net! Was he even the one to do the lift?

-Aaron
4vertical is offline   Reply With Quote
Unread 02-20-2007, 06:14 AM   #10
Gone Wild
 
tungpo1's Avatar
E-Z-GO
 
Join Date: Dec 2006
Location: St. Johns /Jacksonville
Posts: 2,383
Default

The plate are maybe 1/4 inch but its all out of wack tires a wearing bad.
tungpo1 is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


« Battery | Top | Best way »
Thread Tools
Display Modes



All times are GMT -5. The time now is 04:33 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.