lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 12-31-2011, 01:07 PM   #1
Not Yet Wild
Club Car
 
Join Date: Sep 2010
Location: Natchez, MS
Posts: 54
Default No go after motor install

I have just got my motor back and I installed it. When I put it in forward or reverse it would only barely jump. So then I looked at all my diagrams I have and changed a few things but now I cant even get the solenoid to click on. I am not sure what has happened unless my controller blew so any ideas would be greatly appreciated. Oh and it is a 36v 94 CC Ds with 480 amp logisystem controller.
TIA
Zach
Zach_McCormick is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 12-31-2011, 01:12 PM   #2
Cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 64,069
Default Re: No go after motor install

First thing that comes to mind is a wire has been reconnected wrong?
Did you mark everything before taking the motor off?
Did the cart run before the motor was removed?
Lastly what did you change around that made the solenoid stop clicking?
scottyb is offline   Reply With Quote
Unread 12-31-2011, 01:32 PM   #3
Not Yet Wild
Club Car
 
Join Date: Sep 2010
Location: Natchez, MS
Posts: 54
Default Re: No go after motor install

I did mark them before i removed the wires. It ran fine before I removed the motor. But i changed up the spots on the motor terminals. I have it hooked up as this diagram says to now.
Attached Images
File Type: jpg Logisystem003.jpg (69.5 KB, 16 views)
Zach_McCormick is offline   Reply With Quote
Unread 12-31-2011, 02:56 PM   #4
Not Yet Wild
Club Car
 
Join Date: Sep 2010
Location: Natchez, MS
Posts: 54
Default Re: No go after motor install

The thing I do not understand is how the solenoid stop working because I did not change up anything going to or from it. Only thing I changed was from F/R switch to motor and to controller.
Zach_McCormick is offline   Reply With Quote
Unread 01-02-2012, 03:33 PM   #5
Not Yet Wild
Club Car
 
Join Date: Sep 2010
Location: Natchez, MS
Posts: 54
Default Re: No go after motor install

Well at first my only problem was just a battery connection but from the unfortunate events now it is a blown controller.. So I guess I'm gonna have to throw some more money I don't have into this thing because of my ignorance ..
Zach_McCormick is offline   Reply With Quote
Unread 01-02-2012, 03:37 PM   #6
Cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 64,069
Default Re: No go after motor install

I hate to hear that but, there is hardly a one of us who has not, through our own mistakes, smoked a controller.
scottyb is offline   Reply With Quote
Unread 01-02-2012, 03:47 PM   #7
Medicare Recipient
E-Z-GO
 
Join Date: Jun 2011
Location: West Michigan
Posts: 3,543
Default Re: No go after motor install

The only people that do not make mistakes are the ones always sitting on their hands . . .
Stevegrmich is offline   Reply With Quote
Unread 01-04-2012, 08:44 PM   #8
Not Yet Wild
Club Car
 
Join Date: Sep 2010
Location: Natchez, MS
Posts: 54
Default Re: No go after motor install

Well thanks for making me feel little less dumb ha. Fortunately scottyb is gonna hook me up. But which alltrax diagram should I use whenever I go to install it. I know what I had wrong on the last but I'm still gunshy on plugging it up so I wanna be ready whenever it comes in. I looked on alltrax website but didn't really help because all I saw was for shunt wound motors. However, this one from scotty is the one I believe I should use.
Attached Images
File Type: jpg AXE Series Cable install diagram.jpg (86.8 KB, 6 views)
Zach_McCormick is offline   Reply With Quote
Unread 01-04-2012, 08:55 PM   #9
Cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 64,069
Default Re: No go after motor install

This is a diagram for an Ezgo. The diagram for a CC is attached. Don't confuse me like this I'm starting to doubt which throttle I programmed into your controller this am!?
Attached Files
File Type: pdf 96 CC Alltrax.pdf (181.0 KB, 9 views)
scottyb is offline   Reply With Quote
Unread 01-04-2012, 09:04 PM   #10
Not Yet Wild
Club Car
 
Join Date: Sep 2010
Location: Natchez, MS
Posts: 54
Default Re: No go after motor install

Sorry. I am just trying to clear everything up ha. My pot is 0 to 5k though but I did fail to tell that. Hope that is not a problem.
Zach_McCormick is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
Alltrax DCX 500 motor controller install Electric Club Car
New PQ Bandit Motor Install Electric Club Car
self-install motor upgrade 48V club car Electric Club Car
Install a new PQ Executioner motor here is my plan Electric EZGO
Help with Precedent Motor install Electric Club Car


All times are GMT -5. The time now is 05:00 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.