lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 03-30-2013, 04:55 PM   #1
Gone Wild
 
jlmurphy's Avatar
Club Car
 
Join Date: Nov 2010
Location: East to Southeast,Texas
Posts: 186
Default New Upgrade need alltrax programing help

I just upgraded my cart 2006 presedent with an Alltrax DCX 500IQ, PQ Executioner Motor, 400 amp solinoid and #4 welding cables. It is very jerky in forward not as bad in reverse. It showes feild map #4. Alltax sent me 2 Hex files to try Hex#2 and Hex#3. I tried both without any luck. I did notic the feild map # does not change when changing Hex files. any suggestions?
jlmurphy is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 03-30-2013, 05:48 PM   #2
Cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 64,053
Default Re: New Upgrade need alltrax programing help

After you upload said hex file, refresh or close and re open, the map # should change.
scottyb is offline   Reply With Quote
Unread 03-30-2013, 05:59 PM   #3
Gone Wild
 
jlmurphy's Avatar
Club Car
 
Join Date: Nov 2010
Location: East to Southeast,Texas
Posts: 186
Default Re: New Upgrade need alltrax programing help

Tried it again. I went to Tools, Upgrade, Found the Hex file open it, It ran, Refreshed, closed, Opened still showing Field map #4. Still jerking in forward not as bad in reverse.
jlmurphy is offline   Reply With Quote
Unread 03-30-2013, 06:14 PM   #4
Gone Wild
 
Schunter's Avatar
Club Car
 
Join Date: Nov 2010
Location: Auburndale,fl
Posts: 256
Default Re: New Upgrade need alltrax programing help

The hex file they sent me on my other cart was for a custom Throttle,,,Did you check the custom box ??
Schunter is offline   Reply With Quote
Unread 03-30-2013, 06:18 PM   #5
Gone Wild
 
jlmurphy's Avatar
Club Car
 
Join Date: Nov 2010
Location: East to Southeast,Texas
Posts: 186
Default Re: New Upgrade need alltrax programing help

yes custom was checked
jlmurphy is offline   Reply With Quote
Unread 03-30-2013, 07:17 PM   #6
Cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 64,053
Default Re: New Upgrade need alltrax programing help

Maybe map 4 is the file you have? What was it when you looked at it originally?
scottyb is offline   Reply With Quote
Unread 03-30-2013, 09:59 PM   #7
Gone Wild
 
jlmurphy's Avatar
Club Car
 
Join Date: Nov 2010
Location: East to Southeast,Texas
Posts: 186
Default Re: New Upgrade need alltrax programing help

Pushing the foot feed to the right the cart is smooth. pushing it to the left very jerky. What is the foot feed called and where can I buy one.
jlmurphy is offline   Reply With Quote
Unread 03-31-2013, 12:03 AM   #8
Gone Wild
 
Join Date: Jul 2012
Posts: 912
Default Re: New Upgrade need alltrax programing help

Put throttle up rate to 2-4
or get a new MCOR.
Speedchaser is offline   Reply With Quote
Unread 03-31-2013, 07:39 AM   #9
Cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 64,053
Default Re: New Upgrade need alltrax programing help

With the key OFF crawl under the cart while somebody pushes the gas for you. Observe where the slop is and see what can be done to reduce it. I have had some luck with a big pr of channel locks just re-crimping the flimsy aluminum linkage connections.
This is a common CC DS problem
Not sure about the Precedent
scottyb is offline   Reply With Quote
Unread 03-31-2013, 07:57 AM   #10
Gone Wild
 
DJBlade's Avatar
Club Car
 
Join Date: Dec 2011
Location: Columbia, South Carolina
Posts: 258
Default Re: New Upgrade need alltrax programing help

Precedent doesn't have any linkage. There are many quirks about programing. If you change any of the slopes after you install the custom hex file, it will revert some setting back that eliminates the ability to obtain 100% throttle. Lower the uprate, and make the downrate double that of the uprate.

Read here too.... Alltrax Controller Problem in Precedent I say it is an MCOR that had some issues at low amperage, and is exaggerating the problem at higher amperage.
DJBlade is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
New Alltrax DCX 400 Upgrade Kit For Sale Golf Carts and Parts
Alltrax DCX400 PDS upgrade results Electric EZGO
Help Programing Alltrax Controller Electric Club Car
alltrax programing Electric EZGO
Alltrax Programing Extreme DC!


All times are GMT -5. The time now is 07:41 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.