|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
03-30-2013, 03:55 PM | #1 |
Gone Wild
Join Date: Nov 2010
Location: East to Southeast,Texas
Posts: 187
|
New Upgrade need alltrax programing help
I just upgraded my cart 2006 presedent with an Alltrax DCX 500IQ, PQ Executioner Motor, 400 amp solinoid and #4 welding cables. It is very jerky in forward not as bad in reverse. It showes feild map #4. Alltax sent me 2 Hex files to try Hex#2 and Hex#3. I tried both without any luck. I did notic the feild map # does not change when changing Hex files. any suggestions?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-30-2013, 04:48 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,356
|
Re: New Upgrade need alltrax programing help
After you upload said hex file, refresh or close and re open, the map # should change.
|
03-30-2013, 04:59 PM | #3 |
Gone Wild
Join Date: Nov 2010
Location: East to Southeast,Texas
Posts: 187
|
Re: New Upgrade need alltrax programing help
Tried it again. I went to Tools, Upgrade, Found the Hex file open it, It ran, Refreshed, closed, Opened still showing Field map #4. Still jerking in forward not as bad in reverse.
|
03-30-2013, 05:14 PM | #4 |
Gone Wild
Join Date: Nov 2010
Location: Auburndale,fl
Posts: 256
|
Re: New Upgrade need alltrax programing help
The hex file they sent me on my other cart was for a custom Throttle,,,Did you check the custom box ??
|
03-30-2013, 05:18 PM | #5 |
Gone Wild
Join Date: Nov 2010
Location: East to Southeast,Texas
Posts: 187
|
Re: New Upgrade need alltrax programing help
yes custom was checked
|
03-30-2013, 06:17 PM | #6 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,356
|
Re: New Upgrade need alltrax programing help
Maybe map 4 is the file you have? What was it when you looked at it originally?
|
03-30-2013, 08:59 PM | #7 |
Gone Wild
Join Date: Nov 2010
Location: East to Southeast,Texas
Posts: 187
|
Re: New Upgrade need alltrax programing help
Pushing the foot feed to the right the cart is smooth. pushing it to the left very jerky. What is the foot feed called and where can I buy one.
|
03-30-2013, 11:03 PM | #8 |
Gone Wild
Join Date: Jul 2012
Posts: 909
|
Re: New Upgrade need alltrax programing help
Put throttle up rate to 2-4
or get a new MCOR. |
03-31-2013, 06:39 AM | #9 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,356
|
Re: New Upgrade need alltrax programing help
With the key OFF crawl under the cart while somebody pushes the gas for you. Observe where the slop is and see what can be done to reduce it. I have had some luck with a big pr of channel locks just re-crimping the flimsy aluminum linkage connections.
This is a common CC DS problem Not sure about the Precedent |
03-31-2013, 06:57 AM | #10 |
Gone Wild
Join Date: Dec 2011
Location: Columbia, South Carolina
Posts: 258
|
Re: New Upgrade need alltrax programing help
Precedent doesn't have any linkage. There are many quirks about programing. If you change any of the slopes after you install the custom hex file, it will revert some setting back that eliminates the ability to obtain 100% throttle. Lower the uprate, and make the downrate double that of the uprate.
Read here too.... http://www.buggiesgonewild.com/elect...ecedent-5.html I say it is an MCOR that had some issues at low amperage, and is exaggerating the problem at higher amperage. |
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
New Alltrax DCX 400 Upgrade Kit For Sale | Golf Carts and Parts | |||
Alltrax DCX400 PDS upgrade results | Electric EZGO | |||
Help Programing Alltrax Controller | Electric Club Car | |||
alltrax programing | Electric EZGO | |||
Alltrax Programing | Extreme DC! |