|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
12-12-2014, 09:57 AM | #1 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
What is the length of a stock PDS motor?
What I'm looking for the the length from where the housing mounts to the differential to the backside of the endcap, not including any protrusions.
(As shown in the attached drawing) The stock PDS motor I exploded is no longer in my possession, so I cannot measure it. The diameter of cart motor housings is more or less fixed at about 6.7" since they all bolt up to the same differential, but the length isn't and in general terms, more torque is generated by physically larger windings with the same amount of current passing through them. FWIW: The case length on the motor I'm running is roughly 9 3/4". |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
12-12-2014, 10:29 AM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: What is the length of a stock PDS motor?
I have one I can measure when it stops raining
|
12-12-2014, 10:41 AM | #3 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: What is the length of a stock PDS motor?
Is your area getting hit hard?
I saw on the news last night that some places are having floods and mudslides. Hope you and yours are fairing okay..... |
12-12-2014, 12:43 PM | #4 |
Not Yet Wild
Join Date: Mar 2014
Location: Gulf Breeze Florida
Posts: 68
|
Re: What is the length of a stock PDS motor?
9 1/2 inches on the one I have on the bench. This is from the end of the case to the end of the sensor.
|
12-12-2014, 01:12 PM | #5 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: What is the length of a stock PDS motor?
Quote:
I'm going on memory, but I'm pretty sure the D&D motor I put in is was well over an inch longer than the stock PDS motor I pulled out. Thanks for measuring. |
|
12-15-2014, 05:25 PM | #6 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: What is the length of a stock PDS motor?
I found a picture of my PDS motor installed and it was warm enough to venture outside for a while this afternoon (55°F), so I took some pictures of the D&D motor installed.
The distance between the motor/differential interface and the bottom of the label on the differential is the same distance in both pictures and I have the dimension specs for the D&D motor, so I loaded the pictures in MS Paint and got the X-Y coordinates for differential/motor interface, bottom of label and end of motor, and then did a little number crunching. The D&D motor is ~9.75" and from what I can determine, the PDS motor was ~8.75", both measured from/to the same points, respectively. The D&D sure seemed a lot more than an inch longer when putting it in. |
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
WTB Club Car DS Stock length Steering Joint | Golf Carts and Parts | |||
Stock shock length on G9 | Gas Yamaha | |||
Which gas motor to replace the stock motor in a 1994 Marathon GX444? | Gas EZGO | |||
special request. looking for stock rod length robins engine | Gas EZGO | |||
Length of stock rear leaf shackles | Gas EZGO |