|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
08-29-2015, 02:38 PM | #1 |
Getting Wild
Join Date: Jun 2011
Location: Jacksonville, Florida
Posts: 90
|
EZGO won't foward just reverse
I had to replace the bearings on the input so labeled all motor cables removed the motor replaced the input shaft put the motor back on and wired the motor back. now it only goes in reverse solenoid clicks but it wont go
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-29-2015, 04:11 PM | #2 |
Guest
Posts: n/a
|
Re: EZGO won't foward just reverse
|
08-29-2015, 04:36 PM | #3 |
Getting Wild
Join Date: Jun 2011
Location: Jacksonville, Florida
Posts: 90
|
Re: EZGO won't foward just reverse
Early 2001 36volts everything stock except fwd/Rev switch is heavy duty and 2ga cables
|
08-29-2015, 05:06 PM | #4 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: EZGO won't foward just reverse
Sounds like you have a series drive.
If it runs in reverse, but not forward and the solenoid clicks when the pedal is pushed with direction selector lever in forward, the high current contacts in the F/R switch are not making contact. Except for the microswitch that sounds the beeper and put controller into 1/2 speed (if so equipped), all the components used in reverse are used in forward, so the culprit is the F/R contacts. |
08-30-2015, 08:59 AM | #5 |
Getting Wild
Join Date: Jun 2011
Location: Jacksonville, Florida
Posts: 90
|
Re: EZGO won't foward just reverse
F/R switch is only about a year old and it's the HD how can I test this to see if this the problem or not
|
08-30-2015, 09:15 AM | #6 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: EZGO won't foward just reverse
How to check instructions near bottom of webpage: http://www.cartsunlimited.net/F_R_Switch_Upgrades.html
|
08-30-2015, 09:26 AM | #7 |
Getting Wild
Join Date: Jun 2011
Location: Jacksonville, Florida
Posts: 90
|
Re: EZGO won't foward just reverse
Thanks I will check it out
|
08-30-2015, 12:10 PM | #8 |
Getting Wild
Join Date: Jun 2011
Location: Jacksonville, Florida
Posts: 90
|
Re: EZGO won't foward just reverse
This what I got for readings on the F/R switch in the fwd position key off I got 1.4ohms and on the reverse I got 2.2ohms. The carts unlimited page says it should 0.4ohms or less so I'm guessing this is a bad F/R
|
08-31-2015, 08:08 AM | #9 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: EZGO won't foward just reverse
Remember, there is two sets of contacts for Reverse and two sets for Forward.
|
08-31-2015, 08:41 AM | #10 |
Getting Wild
Join Date: Jun 2011
Location: Jacksonville, Florida
Posts: 90
|
Re: EZGO won't foward just reverse
I went back measured it again this time for FWD between posts 5 and 3 I got .6 and 4 and 8 I got .2 I checked these a couple of times. In REV between posts 4 and 5 I got .4 and posts 3 and 8 I got 2.7 again i measured this a couple times.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
ezgo series foward and reverse switch stock | Golf Carts and Parts | |||
foward reverse | Electric EZGO | |||
no foward or reverse | Electric EZGO | |||
Foward in reverse and reverse in forward | Electric Club Car | |||
EZGO Foward/Reverse Backwards ! | Electric EZGO |