|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
11-28-2015, 07:24 PM | #1 |
Not Yet Wild
Join Date: Sep 2015
Posts: 30
|
RXV only creaps very slow in gear
Ezgo RXV with 3 phase motor. Unable to drive will only creap very slowly in gear. Have tested charged batteries ( only 2 years old ) have checked and cleaned all terminals. Batteries will only charge to about 80% ( all cells 1250 )total 50 volts will drop to 48 volts whilst tring to drive. Brakes are releasing have tried to drive on axle stands still the same speed. I suspect a speed sensor but cannot find one fitted. On start up the solenoids click and the controller buzzes as it self checks. Have checked both brake and throttle are fully releasing. Would like some advice to further test for fault
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-30-2015, 02:52 PM | #2 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: RXV only creaps very slow in gear
Check the ohms on the motor temp sensor. (2 small wires that come from the same cover as the 3 large cables on the motor). I think the range should be 400-1300 ohms. Out of range can cause what you are describing.
|
12-02-2015, 05:50 AM | #3 |
Not Yet Wild
Join Date: Sep 2015
Posts: 30
|
Re: RXV only creaps very slow in gear
Checked temp sensor resistance 575ohms within range
Found a good diagnostic link from an old thread from " ez-rider " It could be the motor encoder, will check for a 5 volt supply . Also a 0 volt signal whilst rotating wheels. Any further tests involve "can " signals, unsure how to test these |
12-02-2015, 09:32 AM | #4 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: RXV only creaps very slow in gear
Oscilloscope is one way. I bought a "Diy oscilloscope kit" for $18 (it works, lots of soldering, really fun to build). It came from a "china stuff website" called banggood. It is only a little larger than a cellphone, not a huge beast like a traditional 'scope and can be run from a 9v battery.
|
12-02-2015, 11:02 PM | #5 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: RXV only creaps very slow in gear
Heres the lil scope. It could give more "real data" than the oem scan tool does. Its not the cleanest or super-high resolution tho. But its cheap, and will do the job.
|
12-03-2015, 09:27 PM | #6 |
Not Yet Wild
Join Date: Sep 2015
Posts: 30
|
Re: RXV only creaps very slow in gear
I have a 5 volt supply to encoder probing red and black wires
Probing red and white wires I have 35mvolts stationary , when rotating wheels ( cart jacked up ) have 2.6 volts . Should be close to zero , is this reason to replace motor ( encoder inside motor housing )? Can rock wheels to obtain 4.8 volt ,this tests is good. Tried same test whilst wheels driven by motor still 2.6 volts. Unsure if this is causing my very slow crawl ? |
12-03-2015, 09:41 PM | #7 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: RXV only creaps very slow in gear
The signal cannot be very accurately detected by a DVM (should be 64 on/off pulses per motor revolution, how are you able to detect that with a DVM, also is it a "clean signal"?). The encoder can be replaced by taking the motor apart (not difficult). Some newer motors have the encoder on the outside of the motor (sounds like yours is not one of those). The 2.6v reading is simply an average of hundreds or thousands of 0-to-5v pulses happening far too quickly for the DVM to read
|
12-04-2015, 05:14 AM | #8 |
Not Yet Wild
Join Date: Sep 2015
Posts: 30
|
Re: RXV only creaps very slow in gear
Sorry I should have said. The test advised to test any of two wires for a zero voltage. One wire must be a Can signal ( this gave an unsteady voltage unable to read ) The other wire gave a good voltage reading ( guessing not a Can wire )The encoder wires disappear into the motor housing not even sure what an encoder would look like
|
12-04-2015, 05:28 PM | #9 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: RXV only creaps very slow in gear
White & black wires gave me this. Gets faster (narrower) as speed increases. This cart had a problem in the plug itself, wiggle the plug, and the signal would go away (causing violent jerking of the motor). The "ghosts" were from my phone camera, not cart system.
|
12-07-2015, 12:09 AM | #10 |
Not Yet Wild
Join Date: Nov 2015
Posts: 3
|
Re: RXV only creaps very slow in gear
Denval, I am new to the cart world know nothing compared to the pros on this site, but I had a similar problem with my TXT, as far as no speed/power. I instantly thought I was in for a big $$$ repair. What I found was that the brake pads had separated from the brackets inside the drum and had locked up the drivers side wheel. Once I pulled the drum it became evident and a brake job was in order. Now... good as new. Not sure if this helps but just a suggestion.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Gear oil? Who needs stinkin' gear oil? | Gas Yamaha | |||
'06 Gas TXT stuck in low gear-slow speed | Gas EZGO | |||
8:1 Gear Change - Ring Gear Torque Value? | Electric EZGO | |||
ezgo marathon back gear box? question i describe in depth not sure if its gear box | Gas EZGO | |||
Crf 450 motor in my golf cart,, need gear ratio issue help.. speed to to slow | Big Block Talk! |