2013 RXV won't move

boonesbuggies · 04-12-2017, 05:46 PM

2013 RXV ran fine and then just quit. The brake won't release to move it so its stuck in its tracks. I have a handheld and its showing no codes , the only thing out of place is the throttle is showing 0 volts when petal is pushed. Also the reverse buzzer is not working.

usgicollector · 04-12-2017, 06:21 PM

Is the reverse buzzer no longer any good or not getting power? Cart won't move unless reverse buzzer is working.

cgtech · 04-12-2017, 06:47 PM

Check in the menus for "charger connected = NO", if "YES" cart no go. Something funny going on if no reverse buzzer.

BobBoyce · 04-12-2017, 07:05 PM

Quote:

Originally Posted by boonesbuggies

2013 RXV ran fine and then just quit. The brake won't release to move it so its stuck in its tracks. I have a handheld and its showing no codes , the only thing out of place is the throttle is showing 0 volts when petal is pushed. Also the reverse buzzer is not working.

Take the plastic controller cover loose from the body, flip it over, and check the fuses under the plastic caps. One 10A and one 7.5A, but you can use 10A for the 7.5A one. That 7.5A one is the motor brake fuse, the 10A is the one that feeds power to the keyswitch. Since the reverse buzzer is not sounding, motor brake power + or - is likely not there or there is an open circuit in the motor brake circuit. Also, try unplugging/replugging your main controller connecter a few times to wipe the connections. Put in tow mode first.

boonesbuggies · 04-13-2017, 11:06 AM

Okay I have a little more info now. The reverse buzzer is working. I pulled the cover and didn't find any fuses? I followed the no power instructions under the cover to release the brake it clicked but didn't move. Now I'm getting the HPD/ sequencing fault?

FF Titus · 04-13-2017, 11:29 AM

Pull the acc pedal back, HPD is high pedal disable, IE if the pedal is pressed in a little when the key is on, it's a lockout feature. The pedal maybe a little pressed down.

BobBoyce · 04-13-2017, 12:31 PM

In addition, clean and lubricate the pivot pins and bearing blocks on both pedals so the move easy and smoothly.

boonesbuggies · 04-18-2017, 10:24 AM

Haven't had much time to work on the cart I did try pulling up on the pedal before turning the key on and that didn't work. So today I plan on pulling the matt up and getting a closer look at everything.

boonesbuggies · 04-19-2017, 03:40 PM

Now it's just throwing the "stall detected" code until I go to turn it off and it throws the HPD one again. I cleaned everything and it appears to be working correctly.

boonesbuggies · 04-19-2017, 08:14 PM

when the cart is turned on and you hit the accelerator you can hear what sounds like something turning and then everything quits and the stall code appears

04-12-2017, 05:46 PM	#1
boonesbuggies Getting Wild Join Date: Aug 2016 Location: Seneca South Carolina Posts: 138	2013 RXV won't move 2013 RXV ran fine and then just quit. The brake won't release to move it so its stuck in its tracks. I have a handheld and its showing no codes , the only thing out of place is the throttle is showing 0 volts when petal is pushed. Also the reverse buzzer is not working.

04-12-2017, 06:47 PM	#3
cgtech Over This Interview Is... Join Date: Jun 2012 Location: AZ Posts: 17,449	Re: 2013 RXV won't move Check in the menus for "charger connected = NO", if "YES" cart no go. Something funny going on if no reverse buzzer.

04-13-2017, 11:06 AM	#5
boonesbuggies Getting Wild Join Date: Aug 2016 Location: Seneca South Carolina Posts: 138	Re: 2013 RXV won't move Okay I have a little more info now. The reverse buzzer is working. I pulled the cover and didn't find any fuses? I followed the no power instructions under the cover to release the brake it clicked but didn't move. Now I'm getting the HPD/ sequencing fault?

04-13-2017, 11:29 AM	#6
FF Titus Gone Wild Join Date: Jul 2011 Location: Rhode Island Posts: 489	Re: 2013 RXV won't move Pull the acc pedal back, HPD is high pedal disable, IE if the pedal is pressed in a little when the key is on, it's a lockout feature. The pedal maybe a little pressed down.

04-13-2017, 12:31 PM	#7
BobBoyce Gone Insane Join Date: Oct 2015 Location: TN/NC/GA Tri-state area Posts: 3,952	Re: 2013 RXV won't move In addition, clean and lubricate the pivot pins and bearing blocks on both pedals so the move easy and smoothly.

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

04-18-2017, 10:24 AM	#8
boonesbuggies Getting Wild Join Date: Aug 2016 Location: Seneca South Carolina Posts: 138	Re: 2013 RXV won't move Haven't had much time to work on the cart I did try pulling up on the pedal before turning the key on and that didn't work. So today I plan on pulling the matt up and getting a closer look at everything.

04-19-2017, 03:40 PM	#9
boonesbuggies Getting Wild Join Date: Aug 2016 Location: Seneca South Carolina Posts: 138	Re: 2013 RXV won't move Now it's just throwing the "stall detected" code until I go to turn it off and it throws the HPD one again. I cleaned everything and it appears to be working correctly.

04-19-2017, 08:14 PM	#10
boonesbuggies Getting Wild Join Date: Aug 2016 Location: Seneca South Carolina Posts: 138	Re: 2013 RXV won't move when the cart is turned on and you hit the accelerator you can hear what sounds like something turning and then everything quits and the stall code appears

Similar Threads
Thread	Forum
2013 ez-go rxv	Lifted Golf Carts
2013 RXV does not Move- Brake lights turn on when trying to accelerate	Electric EZGO
2013 Rem DS 7D	Electric Club Car
as of feb 2013	Test Post
1996 Series DS 48V won't move on ground, wheels barely move on jacks	Electric Club Car