|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
04-15-2017, 06:22 PM | #1 |
Gone Wild
Join Date: Jan 2012
Posts: 178
|
Beating my head against the wall..PDS is dead
I've checked the following
Micro switch F/r switch on dash Key switch Installed used controller from member on here It won't do anything. No solenoid click or anything. I've checked all the wires that are supposed to have voltage per JohnnyB's posts. Only other thing I could think is the ITS maybe? Not quite sure how to check it. Thanks in advance for the help |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-15-2017, 07:32 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Beating my head against the wall..PDS is dead
ITS test per the manual
|
04-15-2017, 07:54 PM | #3 |
Gone Wild
Join Date: Jan 2012
Posts: 178
|
Re: Beating my head against the wall..PDS is dead
|
04-16-2017, 09:40 AM | #4 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Beating my head against the wall..PDS is dead
Quote:
With the Run/Tow switch in the Run position, push the cart by hand. The solenoid ought to click and the beeper ought to beep rapidly. If not, the controller is not powered up. Check for FULL battery pack voltage (~38.2V) on J1 Pins 4 & 5 and on all four pins of J3. Also, when cart is ready to drive except for pedal being pushed, what is the voltage on the yellow wire attached to one of the solenoid's small studs? |
|
04-16-2017, 11:52 AM | #5 |
Gone Wild
Join Date: Jan 2012
Posts: 178
|
Re: Beating my head against the wall..PDS is dead
Went back out and looked some more. Mistakenly made it send me a code. I didn't know the Cart would do that. I use to my Marathon. Have me a 1-4 code high pedal switch. I'm now thinking more and more I have a bad ITS. Also read when another fella on the boards had the exact same issue
|
04-16-2017, 12:18 PM | #6 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Beating my head against the wall..PDS is dead
Quote:
Could be debris blocking the pedal from returning to the up position, or weak return spring, or bad pedal switch, or cross-talk between pins in in-line connector between cable from pedal box and cart wiring harness. Please note that the ITS is not among the possibilities listed on the PDS label. (Attached) |
|
04-16-2017, 12:37 PM | #7 | |
Gone Wild
Join Date: Jan 2012
Posts: 178
|
Re: Beating my head against the wall..PDS is dead
Quote:
|
|
04-16-2017, 01:19 PM | #8 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Beating my head against the wall..PDS is dead
I'm just trying to save you (or your cousin) about $50.
Personally, I'd check for proper voltages at J4 Pin-1 before I sprung for an ITS sensor. With pedal down, it will have battery pack voltage (~38.2V) and with pedal up, it has to be close to 0.0V, or you get a HPD error. |
04-16-2017, 03:21 PM | #9 | |
Gone Wild
Join Date: Jan 2012
Posts: 178
|
Re: Beating my head against the wall..PDS is dead
Quote:
|
|
04-16-2017, 03:51 PM | #10 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Beating my head against the wall..PDS is dead
That pretty much eliminates the pedal switch input.
What are the ITS voltages on J4 Pin-4 and Pin-3? |
|
|
Similar Threads | ||||
Thread | Forum | |||
beating the old dead 6098 horse | Gas EZGO | |||
Cart into brick wall !!! | Electric Club Car | |||
piston to wall clearence | Big Block Talk! |