|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
07-15-2017, 11:09 AM | #1 |
Not Yet Wild
Join Date: Nov 2011
Location: ORLANDO, FL
Posts: 25
|
2013 RXV motor stall
2013 RXV, motor stall detected. it runs through power up checklist and creeps 3" forward and dies. Wont re start til you cycle the key and same thing all over again. Only code in handheld is motor stall detected (Like I noticed that too duh LOL) Controller test good Tried another known good motor New speed sensor New controller resistor Tried another known good brake assy. HELP! |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-15-2017, 04:00 PM | #2 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: 2013 RXV motor stall
If it is moving at all during POST, brake is not holding properly.
|
07-17-2017, 06:56 AM | #3 |
Not Yet Wild
Join Date: Nov 2011
Location: ORLANDO, FL
Posts: 25
|
Re: 2013 RXV motor stall
Brake functions as it should
|
07-17-2017, 06:57 AM | #4 |
Not Yet Wild
Join Date: Nov 2011
Location: ORLANDO, FL
Posts: 25
|
Re: 2013 RXV motor stall
it doesn't move until you floor the pedal and it will creep forward about 3"-6" and the motor stalls and brake locks. Remove brake but keep plugged in, makes no difference, so I know nothing is locked up.;
|
07-17-2017, 08:18 AM | #5 |
Gone Wild
Join Date: Apr 2015
Location: Pennsylvania
Posts: 378
|
Re: 2013 RXV motor stall
Since you were able to read the fault I assume you have a handset. Under monitor menu go into the 'Motor' tab and read that RPM input when you try driving it.
1) Should show positive number in forward and negative in reverse. If the +/- does not match F/R then switch pins 30 & 31. 2) If it shows 0 measure unplug the motor sensor plug and measure pins 30 and 31 (I think they are grey and blue...center two of the connector) at the motor plug to B- they should each have a 5V pull-up. If one of these is missing controller is likely bad. |
07-17-2017, 08:31 AM | #6 |
Not Yet Wild
Join Date: Nov 2011
Location: ORLANDO, FL
Posts: 25
|
Re: 2013 RXV motor stall
I sent the controller out to FSIP and it tested good but I will try what you said, Be right back, thanks
|
07-17-2017, 08:51 AM | #7 |
Not Yet Wild
Join Date: Nov 2011
Location: ORLANDO, FL
Posts: 25
|
Re: 2013 RXV motor stall
30 and 31 are grey and blue w/ white. @ motor plug there is a blue w/white but no grey
|
07-17-2017, 08:52 AM | #8 |
Not Yet Wild
Join Date: Nov 2011
Location: ORLANDO, FL
Posts: 25
|
Re: 2013 RXV motor stall
handheld reads zero motor f or r
|
07-17-2017, 08:59 AM | #9 |
Not Yet Wild
Join Date: Nov 2011
Location: ORLANDO, FL
Posts: 25
|
Re: 2013 RXV motor stall
2.8v on grey - 4.6v on the blue w/white wire
|
07-17-2017, 10:20 AM | #10 |
Gone Wild
Join Date: Apr 2015
Location: Pennsylvania
Posts: 378
|
Re: 2013 RXV motor stall
The 0 speed is indicating one of your encoder channels isn't pulsing. Sadly the 1206AC unlike the other curtis ACs do not show the individual channel 'speeds' so I would start with the grey wire first. Make sure you have good continuity from the controller back to that pin, and the same for the blue. If possible you may want to try plugging everything in and checking the voltage on each pin then pushing the cart by hand slowly as possible and make sure you have a toggling signal from about 0 to approx 5v. (on/off) for each channel.
|
Tags |
creeps, dies, motor stall, nogo, rxv |
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Precedent Motor Stall | Electric Club Car | |||
2013 Club Car wanting to do the PQ Assassin motor need advice | Electric Club Car | |||
Upgraded my motor and controller on 2013 drive | Electric Yamaha | |||
Cart Problems: Speed Sensor & Motor Stall | Electric Club Car | |||
G16 Surge-Stall-Surge-Stall... FIXED | Gas Yamaha |