medalist?

TechBill · 04-30-2018, 08:45 PM

I brought this EZ GO. based on serial number I am guessing I have a medalist model. It would often scrap on the bottom whenever I hit a bump in the road.

Today, I pulled rubber mat and reveal a bad rust floor. it look like crossmember is rusted too.

Is it savagable or i need to start looking for a donor frame / cart.

Is there like a golf cart junk yard in Missouri or any of the nearby states?

TechBill · 04-30-2018, 08:48 PM

Uploaded the wrong serial photo. Here the correct one.

TechBill · 04-30-2018, 08:49 PM

Quote:

Originally Posted by TechBill

Uploaded the wrong serial photo. Here the correct one.

Sorry that it's upside down, I upload directly from my phone.

Sir Nuke · 04-30-2018, 09:39 PM

bill....that is only a floor pan....its just a piece of sheet metal.....its only held in by some pop rivets.....pull it all out.....and replace it.

TechBill · 04-30-2018, 11:54 PM

Quote:

Originally Posted by Sir Nuke

bill....that is only a floor pan....its just a piece of sheet metal.....its only held in by some pop rivets.....pull it all out.....and replace it.

I am talking about crossmember that under the floor pan. It shown in the photo.

Right now the golf cart look sort of bent downward in the middle. And the fender on driver side is touching the tire when we make a turn. I am.not sure but I don't think it at normal height

I will try rip out floor pan and take better photo tomorrow to see why it so low where the petals are

Oh the petals to make it go sticks of you go all way to the floor, you have to tap it hard to make it spring back up to off position. Someone hit a travel trailer with it because the petal wouldn't come back up so something under cart is binding the petal shaft or something.

Sir Nuke · 04-30-2018, 11:59 PM

well if its sagging that much.....hope you can weld and have some box tubing available. its that or start looking fir a donor frame.

mgray70 · 05-01-2018, 10:42 AM

If the floor pan is in that bad of shape and the middle of the cart is sagging, I think I'd look another cart.

Sent from my SM-G930R4 using Tapatalk

Sideways · 05-01-2018, 12:47 PM

Quote:

Originally Posted by mgray70

If the floor pan is in that bad of shape and the middle of the cart is sagging, I think I'd look another cart.

Sent from my SM-G930R4 using Tapatalk

I agree, either one or both of the frame rails are possibly compromised as well

TechBill · 05-01-2018, 01:24 PM

I think the frame is gone too far so I am looking around for a replacement frame. If you have a frame that will bolt on a medalist, please send me a message but I would prefer to get it from somewhere that is close to my home unless you know how to ship it that is not cost probative.

thank you

gornoman · 05-01-2018, 02:30 PM

I doubt it is a Medalist, I think it is a TXT. Not that it matters frame wise.

Ooops, my bad, it’s a Medalist.

04-30-2018, 09:39 PM	#4
Sir Nuke Master of All Things Join Date: May 2013 Location: West Columbia, Texas Posts: 17,992	Re: medalist? bill....that is only a floor pan....its just a piece of sheet metal.....its only held in by some pop rivets.....pull it all out.....and replace it.

04-30-2018, 11:59 PM	#6
Sir Nuke Master of All Things Join Date: May 2013 Location: West Columbia, Texas Posts: 17,992	Re: medalist? well if its sagging that much.....hope you can weld and have some box tubing available. its that or start looking fir a donor frame.

05-01-2018, 10:42 AM	#7
mgray70 Gone Wild Join Date: Apr 2013 Location: Deep Run, NC Posts: 2,544	Re: medalist? If the floor pan is in that bad of shape and the middle of the cart is sagging, I think I'd look another cart. Sent from my SM-G930R4 using Tapatalk

05-01-2018, 01:24 PM	#9
TechBill Gone Wild Join Date: Apr 2016 Location: Springfield, MO Posts: 195	Re: medalist? I think the frame is gone too far so I am looking around for a replacement frame. If you have a frame that will bolt on a medalist, please send me a message but I would prefer to get it from somewhere that is close to my home unless you know how to ship it that is not cost probative. thank you

05-01-2018, 02:30 PM	#10
gornoman Stay thirsty my friends! Join Date: Jan 2007 Location: Suburban Chicago Posts: 24,289	Re: medalist? I doubt it is a Medalist, I think it is a TXT. Not that it matters frame wise. Ooops, my bad, it’s a Medalist. Last edited by gornoman; 05-01-2018 at 02:32 PM.. Reason: Ooops....

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

Similar Threads
Thread	Forum
95 36v EZ-GO Medalist won’t run	Electric EZGO
95 medalist w/dcs	Extreme DC!
Txt and medalist	Electric EZGO
What can i do to a 94 medalist?	Electric EZGO