|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
07-24-2018, 01:14 AM | #1 |
Not Yet Wild
Join Date: Sep 2014
Location: Locust grove, Georgia
Posts: 5
|
2006 ezgo txt pds no go-
I have a 2006 EZGO txt PDS 1506 MX controller will not go all the pins show voltage that are required on J-1,J3 & J4 the too small post on solenoid both Show 36 volts regardless unless it's in neutral. The drvoltage drop on the controller side of the solenoid is within specs. The key switch , directional switch , speed sensor, micro sensor and ITP all check as required. My instincts say its the motor however I do question the controller. If I have over looked something please advise. Many thanks in advance.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-24-2018, 01:16 AM | #2 |
Not Yet Wild
Join Date: Sep 2014
Location: Locust grove, Georgia
Posts: 5
|
Re: 2006 ezgo txt pds no go-
Sorry 1206 MX fingers just ain't what they used to be
|
07-24-2018, 10:12 AM | #3 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 2006 ezgo txt pds no go-
Quote:
Does solenoid click when pedal is pushed? If not, does J4 Pin-1 have B+ on it when pedal is pushed? |
|
07-24-2018, 09:27 PM | #4 |
Not Yet Wild
Join Date: Sep 2014
Location: Locust grove, Georgia
Posts: 5
|
Re: 2006 ezgo txt pds no go-
I'm not sure if I'm doing this right or not but here is what I have as of right now. If I place my black probe on J-1 pin 6 and my red probe on B+ on the controller I get bank voltage,. Press accelerator I get no change. If I place my red probe on J-1 pin 1 and my black Probe on B- on the controller I get Bank voltage press the accelerator no change. Cart in run position ignition on in F I have no solenoid click at all
|
07-24-2018, 09:31 PM | #5 |
Not Yet Wild
Join Date: Sep 2014
Location: Locust grove, Georgia
Posts: 5
|
Re: 2006 ezgo txt pds no go-
I'm sorry and J-4 pin 1 has bank until pedal is pressed. Then drops to 0
|
07-25-2018, 11:06 AM | #6 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 2006 ezgo txt pds no go-
Unless otherwise stipulated, all voltages are referenced to B- (Battery pack's main negative terminal)
Attached is a drawing showing how the voltage goes through the various switches to get to the solenoid coil. |
07-29-2018, 09:55 AM | #7 |
Not Yet Wild
Join Date: Sep 2014
Location: Locust grove, Georgia
Posts: 5
|
Re: 2006 ezgo txt pds no go-
My solenoid never clicks. Voltage at small terminals remain the same regardless of peddle location. I suppose I will replace the solenoid and go from there.
|
07-29-2018, 10:53 AM | #8 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 2006 ezgo txt pds no go-
The solenoid isn't activating because the controller is not putting B- on the blue wire, so replacing the solenoid isn't going to fix the problem.
The solenoid has B+ (36V) on the yellow wire, which is feeding through the coil and can be measured on the other small terminal until the controller puts B- on the blue wire, then that terminal goes to 0V and the solenoid clicks. The solenoid is supposed to put B- on the blue when the pedal switch closes, so either the pedal switch is bad, or the controller is bad. What is the voltage on J4 Pins 1 & 2 when pedal is up and when pedal is down? (Pin-2 ought to have 36V on it with pedal up or down while Pin-1 should only have 36v on it when the pedal is down.) |
Tags |
2006 ezgo txt pds, ezgo will not go |
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
2006 ezgo txt w/pds | Electric EZGO | |||
2006 ezgo | Electric EZGO | |||
2006 EZGO Won't run HELP! | Electric EZGO | |||
2006 ezgo txt | Gas EZGO | |||
2006 ezgo gas | Gas EZGO |