still wont go

falconer_39 · 05-01-2009, 05:36 PM

ok guys i am new here
i have read about all the thread about ezgo wont go and i have done all of what yall have said to do but mine is still deader then that road kill on the road mine is a controller i have jumped the silanoid and still nothing just alot of sparks and melting my jumper wire i can put mine in reverse and the little beeper does not work now i am wondering is my motor might be fried. when we pulled it from the woods the right wheel would turn but the left would not .it is a ezgo 1990 all my batteries are new and charged when you mash the pedal the silanoid will click and all my connections are in great shape and all my mico are working
so any ideal what i need to do next
thank you David

pggroves · 05-01-2009, 06:20 PM

What the heck. I'll start you with a chore.

Series motor testing.

Remove pack voltage from system.
Jack up rear wheels and support on jack stands.
Remove and isolate the four cables connected to motor insuring to back up the jam nut on each connection. DO NOT TWIST THE MOTOR TERMINAL STUDS!.

Connect a jumper between the A1 and S1 post.
Use a 12v battery and jumper cables or you can use a 12v battery charger with the start/boost option. Connect the battery or charger to the A2 and S2 posts of the motor. Polarity is not critical and the motor should spin one way or the other.

DO NOT RUN AN ELECTRIC MOTOR WITH THE FRONT SHAFT UNSUPPORTED!

falconer_39 · 05-01-2009, 07:10 PM

Quote:

Originally Posted by pggroves

What the heck. I'll start you with a chore.

Series motor testing.

Remove pack voltage from system.
Jack up rear wheels and support on jack stands.
Remove and isolate the four cables connected to motor insuring to back up the jam nut on each connection. DO NOT TWIST THE MOTOR TERMINAL STUDS!.

Connect a jumper between the A1 and S1 post.
Use a 12v battery and jumper cables or you can use a 12v battery charger with the start/boost option. Connect the battery or charger to the A2 and S2 posts of the motor. Polarity is not critical and the motor should spin one way or the other.

on this please over look my not understanding ok
on a 12 volt battery with a pair of jumper cables hook up the battery as normal and clamp the ground on the body of the cart motor and clamp the hot to the a1 first and then to the s1 or put the jumper on both and then clamp the hot on eather one or do you mean hook the hot to a1 and the ground to s1
the reason i am asking is the way i check a starter is by hooking the ground to the body of the starter and the hot to the selinoid

i am just making sure i understand you before i hook it up

DO NOT RUN AN ELECTRIC MOTOR WITH THE FRONT SHAFT UNSUPPORTED!

ok on this part the front shaft unsupported do you mean do not remove the motor from the axle and try to power it up
thank you for your help
david

Otter70 · 05-01-2009, 07:12 PM

do NOT remove the motor while you test it. test it with it in the cart. good luck

falconer_39 · 05-01-2009, 07:26 PM

ok got you thank you sir

pggroves · 05-01-2009, 09:59 PM

Quote:

Originally Posted by falconer_39

on this please over look my not understanding ok
on a 12 volt battery with a pair of jumper cables hook up the battery as normal and clamp the ground on the body of the cart motor and clamp the hot to the a1 first and then to the s1 or put the jumper on both and then clamp the hot on eather one or do you mean hook the hot to a1 and the ground to s1
the reason i am asking is the way i check a starter is by hooking the ground to the body of the starter and the hot to the selinoid

i am just making sure i understand you before i hook it up

ok on this part the front shaft unsupported do you mean do not remove the motor from the axle and try to power it up
thank you for your help
david

Quote:

Originally Posted by falconer_39

....clamp the ground on the body of the cart motor.....

No, do it exactly as I said.
Put a jumper between A1/S1
Connect your jumper cables to the battery.
Connect one of the jumper cables to the A2.
Touch the other jumper cable to S2. Small spark maybe but motor should spin one way or the other telling you motor is functioning.

Quote:

Originally Posted by falconer_39

the reason i am asking is the way i check a starter is by hooking the ground to the body of the starter and the hot to the selinoid

Forget trying to compare a 12v negative(chassis) ground system like an auto. Carts reference all grounds to battery negative. No chassis grounds on electric carts.

scottyb · 05-01-2009, 10:08 PM

I agree with PG

Never use a frame or body gound on a 36 or 48v system

falconer_39 · 05-02-2009, 11:57 AM

well ok guys
i done the motor test like you said and the motor works fine so what now
i notice that on my seilnoid it has a little black resister in front and hooked on both termnals that is getting pretty hot so hot you can only touch it for a few seconds can it be the reason it dont work and also on my f/r switch there is a white wire not hooked up what do you think it goes too and on the beeper the black wire is unhooked where you think it goes too
thank yall for the help
david

scottyb · 05-02-2009, 12:19 PM

Can you post pics.....of the F&R and disconnected wires? does the micro switch at the F&R work? Nothing works without it.
Everybody wants to test the MOTOR? It is the last thing to go out on these carts

falconer_39 · 05-02-2009, 02:39 PM

ok here is the pictures i hope
like i said the big white wire on the f/r switch is not hooked to any thing
it is wraped around a battery cable and that little black wire goes to the beeper on the first picture and on the second one is the black resister on the selinode that gets pretty hot and over look my bad spelling lol

05-01-2009, 05:36 PM	#1
falconer_39 Getting Wild Join Date: May 2009 Location: millport, al Posts: 86	still wont go ok guys i am new here i have read about all the thread about ezgo wont go and i have done all of what yall have said to do but mine is still deader then that road kill on the road mine is a controller i have jumped the silanoid and still nothing just alot of sparks and melting my jumper wire i can put mine in reverse and the little beeper does not work now i am wondering is my motor might be fried. when we pulled it from the woods the right wheel would turn but the left would not .it is a ezgo 1990 all my batteries are new and charged when you mash the pedal the silanoid will click and all my connections are in great shape and all my mico are working so any ideal what i need to do next thank you David

05-01-2009, 06:20 PM	#2
pggroves steeplejack x Join Date: Jan 2007 Location: Republic of Texas Posts: 3,382	Re: still wont go What the heck. I'll start you with a chore. Series motor testing. Remove pack voltage from system. Jack up rear wheels and support on jack stands. Remove and isolate the four cables connected to motor insuring to back up the jam nut on each connection. DO NOT TWIST THE MOTOR TERMINAL STUDS!. Connect a jumper between the A1 and S1 post. Use a 12v battery and jumper cables or you can use a 12v battery charger with the start/boost option. Connect the battery or charger to the A2 and S2 posts of the motor. Polarity is not critical and the motor should spin one way or the other. DO NOT RUN AN ELECTRIC MOTOR WITH THE FRONT SHAFT UNSUPPORTED!

05-01-2009, 07:12 PM	#4
Otter70 Gone Wild Join Date: Feb 2008 Location: Virginia Beach, Virginia Posts: 234	Re: still wont go do NOT remove the motor while you test it. test it with it in the cart. good luck

05-01-2009, 07:26 PM	#5
falconer_39 Getting Wild Join Date: May 2009 Location: millport, al Posts: 86	Re: still wont go ok got you thank you sir

05-01-2009, 10:08 PM	#7
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,419	Re: still wont go I agree with PG Never use a frame or body gound on a 36 or 48v system

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

05-02-2009, 11:57 AM	#8
falconer_39 Getting Wild Join Date: May 2009 Location: millport, al Posts: 86	Re: still wont go well ok guys i done the motor test like you said and the motor works fine so what now i notice that on my seilnoid it has a little black resister in front and hooked on both termnals that is getting pretty hot so hot you can only touch it for a few seconds can it be the reason it dont work and also on my f/r switch there is a white wire not hooked up what do you think it goes too and on the beeper the black wire is unhooked where you think it goes too thank yall for the help david

05-02-2009, 12:19 PM	#9
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,419	Re: still wont go Can you post pics.....of the F&R and disconnected wires? does the micro switch at the F&R work? Nothing works without it. Everybody wants to test the MOTOR? It is the last thing to go out on these carts

Similar Threads
Thread	Forum
txt pds wont go when hot outside	Electric EZGO
wont run	Gas EZGO
91 36V CC Wont Go!	Electric Club Car
94 Ez Go Wont Go	Electric EZGO
she wont go so EZ	Electric EZGO