|
06-22-2010, 11:44 AM
|
#1 |
|
Not Yet Wild
Join Date: Apr 2010
Posts: 34
|
Running
I have a 1995 TxT Series ezgo just install new controller and cleaned all battery cables it runs fine however it runs faster in reverse than in forward.
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
06-22-2010, 07:19 PM
|
#2 |
|
Gone Wild
Join Date: Jun 2010
Location: Central Florida
Posts: 2,757
|
Re: Running
What type of controller did you install?
|
|
|
|
|
06-23-2010, 08:24 AM
|
#3 |
|
Not Yet Wild
Join Date: Apr 2010
Posts: 34
|
Re: Running
It is a GE 500 with adapter
|
|
|
|
|
06-23-2010, 09:02 AM
|
#4 |
|
Gone Wild
Join Date: Nov 2008
Location: Montgomery, AL
Posts: 1,463
|
Re: Running
did it do this prior to controller install. If so, you may have to check wires on motor.
|
|
|
|
|
06-23-2010, 12:11 PM
|
#5 |
|
Not Yet Wild
Join Date: Apr 2010
Posts: 34
|
Re: Running
It did not run at all tell I put it in and also put new motor
|
|
|
|
|
06-23-2010, 12:46 PM
|
#6 |
|
Not Yet Wild
Join Date: Apr 2010
Posts: 34
|
Re: Running
One more thing if you look at the wiring diagram it has two different one one shows the cable form B+ to the f/r switch A at the top and another one shows A at the bottom which one do I go by.
|
|
|
|
|
06-24-2010, 12:50 AM
|
#7 |
|
Gone Wild
Join Date: Jun 2010
Location: Central Florida
Posts: 2,757
|
Re: Running
A goes to the bottom. C to the top. B towards the batteries and D towards the outside of the cart.
The GE doesn't use the half speed reverse so I'm not sure what would be causing this issue. You said you used the converter for the GE, is it possible that somehow the red and orange wires got crossed up? |
|
|
|
|
06-24-2010, 07:05 AM
|
#8 |
|
Not Yet Wild
Join Date: Apr 2010
Posts: 34
|
Re: Running
Ok will look at to night is there a diagram for this as to what you are refering too
|
|
|
|
|
06-25-2010, 07:09 AM
|
#9 |
|
Not Yet Wild
Join Date: Apr 2010
Posts: 34
|
Re: Running
Ok changed everything around. Did check the wires none crossed. Still no luck however it still did not hardly go forward or reverse, I pulled the orange wire from MS4 and it was fast. Still no go in forward. I put the A to B+,the B to A1, the C to A2 and the D to S2. It seems like it wants to take of fast then dosen't. Can the ITs adapter be bypassed and hooked straight to the controller with out the orange wire and if so which wires would go were. Red,White,Black
|
|
|
|
|
06-25-2010, 10:35 PM
|
#10 |
|
Gone Wild
Join Date: Jun 2010
Location: Central Florida
Posts: 2,757
|
Re: Running
no, unfortunately the ITS adapter can't be bypassed because that controller will not recognize the signal from the ITS without it.
Flight Systems INC is the largest supplier of the GE controller that you have. I would suggest making a phone call to their tech department on this one. Personally I am thinking a bad ITS converter, but it could be a couple of other things as well. |
|
|
|
 |
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Am I running enough oil? | Gas EZGO | |||
| 88 cc not running | Electric Club Car | |||
| 88 cc not running | Electric Club Car | |||
| Its Running | Gas Yamaha | |||
Linear Mode
