|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
05-17-2008, 09:36 AM | #1 |
Not Yet Wild
Join Date: May 2008
Posts: 9
|
help the newb with his resistor cart
Hi all, I'm new to this forum, golf carts, and well, electric vehicles in general LOL. I have done quite a bit of fabrication on jeep, and wiring of them too, but nothing that was run with an electric motor.
now I'm wanting to get into electric vehicles, and figured buying a complete cart needing some work would be a good place to start. I found an old EZGO, (1986) with no batteries, I'm told it's been sitting for a few years and the maintenance person who parked it isn't around so no one knows why, and there are no batteries with it. What is the best way to go about finding any problems with it, can I diagnose any problems with a single 12 volt battery, or do I need the full 36 or 48 volts to even figure out if anything is good. I tried searching first, but am so new, I'm at a loss what to search for LOL here's a few pics, also was $200 a good deal on this? what can anyone tell me about this, or 1986's in general, I read something about low speed heat issues with the resistor, is there answer one that replaces it to eliminate the problem? thanks in advance all. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-17-2008, 12:30 PM | #2 |
nimda
Join Date: Jun 2007
Posts: 13,022
|
re: help the newb with his resistor cart
You got yourself a good ole resistor cart. First thing you should do is put power to the motor and make sure its good. If its bad there no reason to spend the cash on a motor. You can connect a 12 volt automotive battery/or 12 volt charger to the motor to check it.
Start off by disconnecting all the connections to the motor. (might as well just gut the whole thing and start over) Jack up the rear of the cart and place it on jackstands to get the rear wheels off the ground. Take one of the cables you took off and use it to connect A2 and S1 together. (the motor A2 and S1) Take another cable and use it to connect to S2 then connect the other end to your 12 volt + power source. Take another cable and connect it to A1 on the motor....dont hook the loose end up just yet. A charger works better for this because you can make the connection before applying power to it. If you use a charger just hook S2 to positive and the A1 to the negative and turn the charger on. If its all in good working order your motor should spin...if not then something is wrong. Something like this. A2 and S1 together S2 to positive power source A1 to negative power source If your motor works then we can continue with the lessons. LOL! Good luck! |
05-17-2008, 03:37 PM | #3 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: help the newb with his resistor cart
WELCOME, Swamper.
Atleast you got one from one of 3 major makers - not some obsolete and obscure thing! Follow Roady's advice and you will be okay. It is a matter of geographics when the price of a project cart is discussed. Also some I paid nothing for cost me a fortune and some I paid alot for taught me alot. Hopefully this one's gonna teach you alot! |
05-17-2008, 06:57 PM | #4 |
steeplejack x
Join Date: Jan 2007
Location: Republic of Texas
Posts: 3,382
|
Re: help the newb with his resistor cart
With the right parts you can make that 86 look EXACTLY like a 94. A lot of the parts can still be found although they are getting a bit scarce.
You can even easily convert the electrical system to a modern controller system. Pretty much anything is possible given the will, $$$$, and "bosses" permission!!! |
05-17-2008, 10:49 PM | #5 |
Golf Cart Photographer
Join Date: Jan 2007
Location: Wichita Falls Texas - My Ride 2010 Club Car
Posts: 6,236
|
Re: help the newb with his resistor cart
Welcome.......................
|
05-18-2008, 05:23 AM | #6 |
Gone Wild
Join Date: Mar 2008
Posts: 291
|
Re: help the newb with his resistor cart
welcome to bgw!!! lots of people here with alot of know how information!!!
|
05-18-2008, 12:24 PM | #7 |
Not Yet Wild
Join Date: May 2008
Posts: 9
|
Re: help the newb with his resistor cart
thanks all, once I get to test it, I will let you all know how it goes...
|
05-28-2008, 06:13 AM | #8 |
Not Yet Wild
Join Date: May 2008
Posts: 9
|
Re: help the newb with his resistor cart
|
05-28-2008, 06:39 AM | #9 | |
Not Yet Wild
Join Date: May 2008
Posts: 9
|
Re: help the newb with his resistor cart
Quote:
|
|
05-28-2008, 06:51 AM | #10 |
Not Yet Wild
Join Date: May 2008
Posts: 9
|
Re: help the newb with his resistor cart
so looking over the cart, and the little I have picked up abotu carts, I would like info on doign the following, after I get up and running with the current set up, I would like to convert to a 48v system, what should I look for in parts for the 48v controller, what other parts are needed? what charger?
oh and one front spring is missing, any info special about that? tires are shot, what type are these? are there cheap replacements? or just match up what they say on the side? |
|
|
Similar Threads | ||||
Thread | Forum | |||
resistor cart | Electric Club Car | |||
G16 Newb | Gas Yamaha | |||
Another newb question | Gas Yamaha | |||
36volt resistor cart to a 48volt? | Electric EZGO |