lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric EZGO
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV.



Post New Thread  Reply
Thread Tools Display Modes
Unread 10-15-2011, 05:39 PM   #1
Gone Wild
E-Z-GO
 
Join Date: Jul 2011
Location: Houston, TX
Posts: 2,904
Default I Really Need Some Expert Help!

Alright, as most of you know I had a bad experience with my last Alltrax DCX 400. Everything was hooked up according to the manual. So...... I am not sure I what could have gone wrong. Can somebody please post picures or diagrams exactly how it should be wired up on my 2002 PDS 36v cart? Everything from rocker switch, key switch, charge receptacle, motor, controller, solenoid, resistor and diode so we don't have another incident. Thanks

Colton
Coltf1991 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 10-15-2011, 05:52 PM   #2
go to cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 68,551
Default Re: I Really Need Some Expert Help!

This diagram is from the Alltrax website.... found in their 'Document Depot'

http://alltraxinc.com/files/Doc100-0...T-wire-dia.pdf
scottyb is offline   Reply With Quote
Unread 10-15-2011, 06:00 PM   #3
Gone Wild
E-Z-GO
 
Join Date: Jul 2011
Location: Houston, TX
Posts: 2,904
Default Re: I Really Need Some Expert Help!

Does it matter what order everything is hooked up in? Also just to try and get it all running does my controller have to be programmer for my bandit motor initially?
Coltf1991 is offline   Reply With Quote
Unread 10-15-2011, 06:08 PM   #4
go to cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 68,551
Default Re: I Really Need Some Expert Help!

That is a good question for PQ. I would like to see them post the answer on the board for all PDS owners to benefit from.

As far as order of wiring? Just be sure the run/tow switch is in the off position until all the wiring is complete ~ wait 30 seconds and flip to run.
scottyb is offline   Reply With Quote
Unread 10-15-2011, 06:15 PM   #5
Gone Wild
E-Z-GO
 
Join Date: Jul 2011
Location: Houston, TX
Posts: 2,904
Default Re: I Really Need Some Expert Help!

Okay. If anybody had an Alltrax PDS controller pictured all wired up I would much appreciate it.
Coltf1991 is offline   Reply With Quote
Unread 10-15-2011, 06:49 PM   #6
.......BGW........
 
rib33024's Avatar
 
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 15,351
Default Re: I Really Need Some Expert Help!

'07 EZGO Build......
rib33024 is online now   Reply With Quote
Unread 10-15-2011, 07:00 PM   #7
Gone Wild
E-Z-GO
 
Join Date: Jul 2011
Location: Houston, TX
Posts: 2,904
Default Re: I Really Need Some Expert Help!

That doesn't show the solenoid wiring but helps with the others. I'm just scared of making another one release smoke. Are the red and yellow wires supposed to go on the same small terminal?
Coltf1991 is offline   Reply With Quote
Unread 10-15-2011, 08:27 PM   #8
go to cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 68,551
Default Re: I Really Need Some Expert Help!

This is the PDS stock wiring diagram, The solenoid wiring does not change when upgrading to 200 amps or 400 amps or 48 volts. The solenoid is wired as the original diagram regardless of amperage or voltage. As I've said before it has no polarity. The 2 small posts are the activation or coil circuit. This circuit has no polarity, only the diode has a polarity. These 2 small terminals require pack voltage to activate and connect the large posts which are the switched circuit... I hope this helps there are colors noted on the original wiring diagram
Ezgo PDS diagram
Attached Images
File Type: jpg Ezgo PDS diagram.JPG (117.0 KB, 119 views)
scottyb is offline   Reply With Quote
Unread 10-15-2011, 08:36 PM   #9
Gone Wild
E-Z-GO
 
Join Date: Jul 2011
Location: Houston, TX
Posts: 2,904
Default Re: I Really Need Some Expert Help!

That helps. So nobody has a picture of one all wired up?
Coltf1991 is offline   Reply With Quote
Unread 10-16-2011, 07:09 AM   #10
??????
 
LostHusker's Avatar
E-Z-GO
 
Join Date: Sep 2009
Location: South TX
Posts: 8,617
Default Re: I Really Need Some Expert Help!

Quote:
Originally Posted by Coltf1991 View Post
That helps. So nobody has a picture of one all wired up?
Did you not pay attention to the cart when you took it apart and take notes?
LostHusker is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric EZGO


Thread Tools
Display Modes


Similar Threads
Thread Forum
Looking for a CV Clutch expert Gas golf carts
I need a battery EXPERT! Electric golf carts
wiring expert needed Electric golf carts
Hello People - I could use some expert advice Electric EZGO


All times are GMT -5. The time now is 09:50 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.