Turn signal and brake light wiring

ezgo2009 · 10-04-2008, 11:12 AM

Where would I ground it to then? a negative wire? Would this cause the fuze to blow? lastly, is there a way to tell, I now get not even the clicking sound from the flasher.

ezgo2009 · 10-04-2008, 11:14 AM

Where to then? now I do not even get a clicking sound from the flasher. and have blown another fuse

gornoman · 10-04-2008, 11:21 AM

You must ground back to a negative 12v reference on the battery pack. If you don't know how to do this, stop now, or you will burn more fuses...

ezgo2009 · 10-04-2008, 11:26 AM

The box says white wire added as a ground to t/s. What is T/s?

rusty · 10-04-2008, 11:50 AM

Tail Light and Signal light........... usually

ezgo2009 · 10-04-2008, 11:52 AM

Thank you, so if I just go to the negative poston the battery, it should work?

rusty · 10-04-2008, 11:57 AM

Yes Negative for your ground........ and if in doubt,...... get a volt meter and measure for 12 to 14 volts on the circuit you will be using before hooking up the wires and burning out bulbs.

rusty · 10-04-2008, 12:01 PM

Oh,.......... By the way...............

Welcome to the forum ezgo2009...............

ezgo2009 · 10-04-2008, 02:14 PM

Thanks this is helping, but I still get nothing, checked and doble checked conections but nothing. Hooked up ground(white) to neg on battery, wires are tight and the way the diagram says, blew fuze when i un did the ground. in line fuse should blo first? I should give up and go fishing!

Andy4639 · 10-05-2008, 09:46 AM

Look at your lights. Are they grounded through a wire or is the housing grounded. You need to know which to run the wires correctley. The housing of each light needs a ground to it ran back to the 12 volt - terminal.
I have had to rewire complete carts because they used the hot wires for grounds instead of using a ground wire. Just because a light has two wires connected to it doesn't mean it's the right 2. You need at least 3 wires running out of each housing and know which is which.

10-04-2008, 11:12 AM	#11
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16	Re: Turn signal and brake light wiring Where would I ground it to then? a negative wire? Would this cause the fuze to blow? lastly, is there a way to tell, I now get not even the clicking sound from the flasher.
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16

10-04-2008, 11:14 AM	#12
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16	Re: Turn signal and brake light wiring Where to then? now I do not even get a clicking sound from the flasher. and have blown another fuse
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16

10-04-2008, 11:21 AM	#13
gornoman Two Cheeks Sliding Join Date: Jan 2007 Location: Suburban Chicago Posts: 2,358	Re: Turn signal and brake light wiring You must ground back to a negative 12v reference on the battery pack. If you don't know how to do this, stop now, or you will burn more fuses...

10-04-2008, 11:26 AM	#14
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16	Re: Turn signal and brake light wiring The box says white wire added as a ground to t/s. What is T/s?
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16

10-04-2008, 11:50 AM	#15
rusty The Welcome Guy Join Date: Jan 2007 Location: Wichita Falls Texas - My Rides 1996 E-Z-GO and 2002 Club Car IQ and 2003 Club Car IQ Posts: 3,065	Re: Turn signal and brake light wiring Tail Light and Signal light........... usually

10-04-2008, 11:52 AM	#16
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16	Re: Turn signal and brake light wiring Thank you, so if I just go to the negative poston the battery, it should work?
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16

10-04-2008, 11:57 AM	#17
rusty The Welcome Guy Join Date: Jan 2007 Location: Wichita Falls Texas - My Rides 1996 E-Z-GO and 2002 Club Car IQ and 2003 Club Car IQ Posts: 3,065	Re: Turn signal and brake light wiring Yes Negative for your ground........ and if in doubt,...... get a volt meter and measure for 12 to 14 volts on the circuit you will be using before hooking up the wires and burning out bulbs.

10-04-2008, 12:01 PM	#18
rusty The Welcome Guy Join Date: Jan 2007 Location: Wichita Falls Texas - My Rides 1996 E-Z-GO and 2002 Club Car IQ and 2003 Club Car IQ Posts: 3,065	Re: Turn signal and brake light wiring Oh,.......... By the way............... Welcome to the forum ezgo2009...............

10-04-2008, 02:14 PM	#19
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16	Re: Turn signal and brake light wiring Thanks this is helping, but I still get nothing, checked and doble checked conections but nothing. Hooked up ground(white) to neg on battery, wires are tight and the way the diagram says, blew fuze when i un did the ground. in line fuse should blo first? I should give up and go fishing!
ezgo2009 Not Yet Wild Join Date: Oct 2008 Posts: 16

10-05-2008, 09:46 AM	#20
Andy4639 Gone Wild Join Date: Jan 2007 Location: Liberty SC Posts: 537	Re: Turn signal and brake light wiring Look at your lights. Are they grounded through a wire or is the housing grounded. You need to know which to run the wires correctley. The housing of each light needs a ground to it ran back to the 12 volt - terminal. I have had to rewire complete carts because they used the hot wires for grounds instead of using a ground wire. Just because a light has two wires connected to it doesn't mean it's the right 2. You need at least 3 wires running out of each housing and know which is which.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
EZGO brake light switch	Electric EZGO
Brake light switch	Gas Yamaha
48v light wiring diagrams	Electric Club Car
Brake light ?	Gas Yamaha
93 ez-go directional light wiring	Gas EZGO