|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
08-05-2008, 08:42 PM | #1 |
Getting Wild
Join Date: Apr 2008
Location: Nara Visa,NM
Posts: 79
|
Microswtches!!!!
I asked b4 and was told that i needed to go by the 70 diagram for my cart cuz motor is in middle of the batteries. Now, It looks like the accerator micro has just one wire going to it(from F&R switch). My microswitch has 3 terminal(has 3 screws) and I would like to know where to put the wire, term 1,2 or 3???? Sorry for buggin you all but I am have h e double l with this thing Got 3 carts and all seem to be wired diff ARGGGGGGHHHHHHH!!!!
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-05-2008, 08:51 PM | #2 |
nimda
Join Date: Jun 2007
Posts: 13,022
|
Re: Microswtches!!!!
You have 3 connections. One says CO (common) one says NC (normally closed) and one says NO (normally open). You will use common for sure and if you are supposed to MAKE a connection with the switch you will use NO, if you want to break a connection with the switch you will use NC.....so CO and NO.
(CO) Common is alway hot....or ground depending how it's wired. |
08-06-2008, 06:41 PM | #3 |
Totally Bonkers!
Join Date: Feb 2008
Location: Full time RVing
Posts: 1,897
|
Re: Microswtches!!!!
Dang roady...you so smart...LOL
|
08-06-2008, 07:03 PM | #4 |
Stay thirsty my friends!
Join Date: Jan 2007
Location: Suburban Chicago
Posts: 24,283
|
Re: Microswtches!!!!
A switch with 1 wire attached does nothing. There must allways be 2 wires (minimum) connected to any switch in any application.
|
08-06-2008, 08:53 PM | #5 |
Getting Wild
Join Date: Apr 2008
Location: Nara Visa,NM
Posts: 79
|
Re: Microswtches!!!!
hummmmm,,, I may not have good enuff eyes to see but I canot see any other wire coming off the accel ms...........
|
08-06-2008, 08:59 PM | #6 |
nimda
Join Date: Jun 2007
Posts: 13,022
|
Re: Microswtches!!!!
Then that is a problem. Every microswitch I have ever seen has at least 2 wires....it simply will not work with 1 wire. 1 wire leads to what you are switching on/off and the second wire leads to the power source.
|
08-06-2008, 09:49 PM | #7 |
Getting Wild
Join Date: Apr 2008
Location: Nara Visa,NM
Posts: 79
|
Re: Microswtches!!!!
you would think that but the diagram only shows one wire and it goes to the forward reverse switch. I dont know what to do LOL
|
08-06-2008, 09:57 PM | #8 |
nimda
Join Date: Jun 2007
Posts: 13,022
|
Re: Microswtches!!!!
Unless the switch is grounded through the body of the microswitch 1 wire does nothing. I'm not sure what you have but something isn't right or just overlooked.
|
08-06-2008, 10:04 PM | #9 |
Getting Wild
Join Date: Apr 2008
Location: Nara Visa,NM
Posts: 79
|
Re: Microswtches!!!!
It is a 85 ezgo . I have an 84 that has the resistors inbetween the batteries and motor over the left side of axle mounted sidways. This 85 has the motor mounted in front of axle and the resistor on the left side above the axle. I may just wire it like the 84 and use the the other diagram.
|
08-06-2008, 10:23 PM | #10 |
steeplejack x
Join Date: Jan 2007
Location: Republic of Texas
Posts: 3,382
|
Re: Microswtches!!!!
|