2000 TXT ITS won't go

meempdog · 08-14-2008, 08:58 PM

Was using my cart last week and heard a popping noise and looked under seat and saw controller somking. Replaced curtis controller with Alltrax and put new solenoid in. When I turn key, put cart in forward; I here a click and get 4 blinking green lights followed by a solid green on my controller. The only problem is the cart doesn't move. Same in reverse. I have checked microswitches on FNR and get 36v on both in neutral, in forward one get 36v and the other 0, in reverse both are zero. Any help on what I should try next would be great. I have checked all wires and ITS box.

roady89 · 08-14-2008, 09:05 PM

Welcome to BGW

Did you check your ITS? 0% throttle should be around .4 volts, 100% throttle should be around 1.4 volts. Anything else and the ITS is bad. Also, are you SURE you got the right throttle type pogrammed into the controller? They generally do a good job of making sure you get the right one BUT they are human and do make mistakes, I know, I have gotten 2 that were programmed wrong.

meempdog · 08-14-2008, 09:14 PM

Thanks

I have not checked ITS yet, only looked at wires. My controller is a NPX because it is a series motor stock.

roady89 · 08-14-2008, 09:19 PM

Ok, the controller SHOULD be programmed for your throttle type. I'm sure they asked you what throttle type you had OR at least what year, make the cart was. Check the ITS and report back.

rusty · 08-14-2008, 09:58 PM

Welcome to the forum meempdog.....................

meempdog · 08-15-2008, 07:16 PM

ITS voltage good

meempdog · 08-17-2008, 05:12 PM

Still having no luck getting cart to go. Getting click and right controller lights but no go. Somebody please help.

roady89 · 08-17-2008, 05:19 PM

Service Repair Manual

Owner's Manual & Service Guide

Service Parts Manual

series controller wiring schematic

cartworldinc · 08-17-2008, 06:42 PM

The four blinks followed by the solid green indicates that the controller is set for the ITS and is reading it correctly. The solid green indicates that you controller is powered up correctly. If there were any field problems it would blink 4 reds. Here is what to look for. An Alltrax powers up automatically when you switch the cart on and the F&R lever is engaged. However without throttle input it will cut itself off after about five or ten seconds. Your controller should power down in that time and the light will go off. Does this happen? Next after the light goes off you should be able to reactivate the controller by use of the accelerator pedal. If you can mash the accelerator and your controller does not power back on, the problem is most likely in the microswitch in your pedal box. If it does power the controller back on your problem is most likely in the contacts in your F&R. Hope this helps

meempdog · 08-18-2008, 07:07 AM

Am I supposed to have a LED indication on the Alltrax controller when I turn the key on or only when I step on pedal?

08-14-2008, 08:58 PM	#1
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5	2000 TXT ITS won't go Was using my cart last week and heard a popping noise and looked under seat and saw controller somking. Replaced curtis controller with Alltrax and put new solenoid in. When I turn key, put cart in forward; I here a click and get 4 blinking green lights followed by a solid green on my controller. The only problem is the cart doesn't move. Same in reverse. I have checked microswitches on FNR and get 36v on both in neutral, in forward one get 36v and the other 0, in reverse both are zero. Any help on what I should try next would be great. I have checked all wires and ITS box.
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5

08-14-2008, 09:05 PM	#2
roady89 nimda Join Date: Jun 2007 Posts: 13,022	Re: 2000 TXT ITS won't go Welcome to BGW Did you check your ITS? 0% throttle should be around .4 volts, 100% throttle should be around 1.4 volts. Anything else and the ITS is bad. Also, are you SURE you got the right throttle type pogrammed into the controller? They generally do a good job of making sure you get the right one BUT they are human and do make mistakes, I know, I have gotten 2 that were programmed wrong.
roady89 nimda Join Date: Jun 2007 Posts: 13,022

08-14-2008, 09:14 PM	#3
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5	Re: 2000 TXT ITS won't go Thanks I have not checked ITS yet, only looked at wires. My controller is a NPX because it is a series motor stock.
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5

08-14-2008, 09:19 PM	#4
roady89 nimda Join Date: Jun 2007 Posts: 13,022	Re: 2000 TXT ITS won't go Ok, the controller SHOULD be programmed for your throttle type. I'm sure they asked you what throttle type you had OR at least what year, make the cart was. Check the ITS and report back.
roady89 nimda Join Date: Jun 2007 Posts: 13,022

08-14-2008, 09:58 PM	#5
rusty Golf Cart Photographer Join Date: Jan 2007 Location: Wichita Falls Texas - My Ride 2010 Club Car Posts: 6,236	Re: 2000 TXT ITS won't go Welcome to the forum meempdog.....................

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

08-15-2008, 07:16 PM	#6
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5	Re: 2000 TXT ITS won't go ITS voltage good
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5

08-17-2008, 05:12 PM	#7
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5	Re: 2000 TXT ITS won't go Still having no luck getting cart to go. Getting click and right controller lights but no go. Somebody please help.
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5

08-17-2008, 05:19 PM	#8
roady89 nimda Join Date: Jun 2007 Posts: 13,022	Re: 2000 TXT ITS won't go Service Repair Manual Owner's Manual & Service Guide Service Parts Manual
roady89 nimda Join Date: Jun 2007 Posts: 13,022

08-17-2008, 06:42 PM	#9
cartworldinc Not Yet Wild Join Date: Aug 2008 Posts: 67	Re: 2000 TXT ITS won't go The four blinks followed by the solid green indicates that the controller is set for the ITS and is reading it correctly. The solid green indicates that you controller is powered up correctly. If there were any field problems it would blink 4 reds. Here is what to look for. An Alltrax powers up automatically when you switch the cart on and the F&R lever is engaged. However without throttle input it will cut itself off after about five or ten seconds. Your controller should power down in that time and the light will go off. Does this happen? Next after the light goes off you should be able to reactivate the controller by use of the accelerator pedal. If you can mash the accelerator and your controller does not power back on, the problem is most likely in the microswitch in your pedal box. If it does power the controller back on your problem is most likely in the contacts in your F&R. Hope this helps
cartworldinc Not Yet Wild Join Date: Aug 2008 Posts: 67

08-18-2008, 07:07 AM	#10
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5	Re: 2000 TXT ITS won't go Am I supposed to have a LED indication on the Alltrax controller when I turn the key on or only when I step on pedal?
meempdog Not Yet Wild Join Date: Aug 2008 Posts: 5

Similar Threads
Thread	Forum
2000 4 cycle gas e-z-go	Gas EZGO
2000 ez go	Gas EZGO
2000 Xrt	Gas Club Car
2000 Ezgo W/PDS	Members Rides
Look for a 2000.5 and up Club Car top	Golf Carts and Parts