|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
04-05-2014, 08:26 PM | #1 |
Not Yet Wild
Join Date: Apr 2014
Posts: 19
|
Was programming alltrax 400 dcx and now cart is dead
cart has brand new batteries and everything was going fine. I wanted to turn down the power and speed for my daughter and her friend to ride it around the yard. After going in and making the changes, I hit set and turned off the key and unplugged the cable and laptop. Turned on the key and nothing. Solenoid clicks but nothing happens when the pedal is pushed. I'm totally lost and need help.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-05-2014, 08:32 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Was programming alltrax 400 dcx and now cart is dead
What did you change?
Check throttle is EZ ITS throttle is a value higher than 50% |
04-05-2014, 08:37 PM | #3 |
Not Yet Wild
Join Date: Apr 2014
Posts: 19
|
Re: Was programming alltrax 400 dcx and now cart is dead
I changed the max speed to 50% and power to 70%
That's all I changed. I even tried to go back and and reset it to default. Solenoid clicks and nothing more. I tested the two inner terminals of solenoid and get full voltage when pedal is pressed |
04-05-2014, 08:47 PM | #4 |
Not Yet Wild
Join Date: Apr 2014
Posts: 19
|
Re: Was programming alltrax 400 dcx and now cart is dead
Also, the controller power light flashes 4 times and turns green when the pedal is pushed. After about 15 seconds, the solenoid clicks again.
|
04-06-2014, 06:25 AM | #5 |
Gone Wild
Join Date: Jan 2013
Location: Sun Lakes, Arizona
Posts: 610
|
Re: Was programming alltrax 400 dcx and now cart is dead
Sounds VERY familiar... happened to me twice when adjusting mine months apart from one another.
|
04-06-2014, 08:24 AM | #6 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Was programming alltrax 400 dcx and now cart is dead
Flip the toggle to tow and disconnect the main neg cable for 30 sec. Re-connect power and flip to run - any change?
Try re-setting defaults again... |
04-06-2014, 11:20 AM | #7 |
Not Yet Wild
Join Date: Apr 2014
Posts: 19
|
Re: Was programming alltrax 400 dcx and now cart is dead
ScottyB I tried doing that and still nothing. After thinking of things that could possibly made it go haywire is: I crossed a small Creek with about 1 ft of water but it didn't even get over the floor board. And still drove fine for about 10 minutes after that. I hooked up the cable and software, made some adjustments. Tried it out and was still to fast for her, plugged it back in to cable. Adjusted it again. Went to try it out and ut oh.. Nothing. No pops or smoke or anything. Solenoids clicks and controller power led is on.
|
04-06-2014, 11:20 AM | #8 |
Not Yet Wild
Join Date: Apr 2014
Posts: 19
|
Re: Was programming alltrax 400 dcx and now cart is dead
|
04-06-2014, 12:09 PM | #9 |
Gone Wild
Join Date: Nov 2012
Location: Ontario , Canada
Posts: 609
|
Re: Was programming alltrax 400 dcx and now cart is dead
I believe he had Alltrax send him out another controller
If my memory is correct |
04-06-2014, 02:43 PM | #10 | |
Gone Wild
Join Date: Sep 2012
Location: Savannah, GA
Posts: 2,760
|
Re: Was programming alltrax 400 dcx and now cart is dead
Quote:
|
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Programming Alltrax controller | Electric EZGO | |||
Alltrax Programming | Electric EZGO | |||
Bad OBC after programming Alltrax controller? possible? | Electric Club Car | |||
alltrax programming | Electric EZGO | |||
Alltrax axe programming | Electric EZGO |