|
Electric golf carts Harley Davidson, Melex, Pargo, Taylor-Dunn and other Misc. Carts. |
|
Thread Tools | Display Modes |
05-26-2009, 06:38 PM | #1 |
Not Yet Wild
Join Date: May 2009
Posts: 6
|
cart will not move
EZ Go apprx 1987.When checking electrical circuts I have current all the way to motor whether key is on or off, but cart will not move.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-27-2009, 07:00 AM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: cart will not move
Welcome earl, what is the pack voltage? With the key on do you hear the solenoid click when you press the gas?
|
05-28-2009, 10:51 AM | #3 |
Not Yet Wild
Join Date: May 2009
Posts: 6
|
Re: cart will not move
Pack voltage is 36 volts and no it does not click. I have put in a new celonid but it didnt help. Thank you--
|
05-28-2009, 02:07 PM | #4 | |
steeplejack x
Join Date: Jan 2007
Location: Republic of Texas
Posts: 3,382
|
Re: cart will not move
Quote:
|
|
05-29-2009, 12:56 PM | #5 |
Not Yet Wild
Join Date: May 2009
Posts: 6
|
Re: cart will not move
unable to locate manufacuter number where should I looik? I thought apprx 1987 because thats what the generator placard says.Thank you!
|
05-29-2009, 02:51 PM | #6 |
steeplejack x
Join Date: Jan 2007
Location: Republic of Texas
Posts: 3,382
|
Re: cart will not move
If in 87 range, tag s/b under passenger glove box. If not there or if no "evidence" (holes) that is was there, then pull up seat and look under driver's butt in the wheel well area.
Pics of battery compartment will identify your system as well. Is traction motor parallel to or perpendicular to axle? |
06-01-2009, 08:14 PM | #7 |
Not Yet Wild
Join Date: May 2009
Posts: 6
|
Re: cart will not move
It is parallel to the axel. The make is golf and country by western body on an ezgo frame 1989. Found a number under seat on the frame 20063449. Replaced the microswitch which is activated by the accelator pedal. The other one did not work. I still get power all the way back to the motor key on or key off. Voltage light shows very bright on left side of celenoid and dimmer light on rt. side. Thank you
|
06-01-2009, 08:39 PM | #8 |
Gone Wild
Join Date: Mar 2009
Location: Roseville, CA
Posts: 2,757
|
Re: cart will not move
Sounds like you have an older Model 200 Western. It should have been built on an EZGO chassis with EZGO running gear.
I have a Western cart and back in 87 it may have been available in 3 different voltages 36, 42 and 48, which one do you have? Does it have resistor coils or a controller? It's a series cart and they were wired the same as EZGO carts with oddball wiring for the lights and 42v stuff. Check these diagrams: http://www.buggiesgonewild.com/elect...g-manuals.html My cart is a 1998 model 400, 42volt, runs on EZGO running gear/chassis and uses a 36vHS series motor, 8:1 gears, 1205 Curtis controller, runs 21 mph with clubs and the windshield up. |
06-02-2009, 07:59 PM | #9 |
Not Yet Wild
Join Date: May 2009
Posts: 6
|
Re: cart will not move
I have a 36 volt and it has resistor coils. Thank you for the diagrams they were helpful. I jury rigged the electric wires on different connectors and got it to actually move. However, I have been unable to duplicate that movment.Thank you--
|
07-29-2009, 07:04 PM | #10 |
Not Yet Wild
Join Date: May 2009
Posts: 6
|
Re: cart will not move
I want to thank everyone for their help. After finally finding and replacing two microswitches we are up and running and have been since July 4/ I sure know a lot more about the mechanics of the cart than I did before. This forum was so helpful to me.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
EZGO DCS Cart won't Move | Electric EZGO | |||
cart wont move | Electric EZGO | |||
Cart won't move | Electric EZGO | |||
Cart Wants to Move But Won't! | Electric Yamaha | |||
93 36V cart wont move | Electric Club Car |