lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Yamaha
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles



Post New Thread  Reply
Thread Tools Display Modes
Unread 04-09-2018, 10:16 AM   #1
Not Yet Wild
 
JakeJones8's Avatar
Yamaha
 
Join Date: May 2017
Location: Dallas, TX
Posts: 66
Default MOT-D2 motor not sitting flush on G29

Anyone put the Admiral MOT-D2 high speed motor on their Yamaha Drive??

I for the life of me canít get the motor to sit flush on the differential mount (see pics). I know something is wrong because I can take the old motor and slide it on and off like butter!!!

I have tried everything under the sun and it almost appears as if the inside ring of the motor housing is smaller than the outside ring on the differential mounting. It slides perfectly until the very end and just hits a brick wall. I can spin it in every direction but it never slides all the way on. Was told do not try and tighten until completly flush.

JakeJones8 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 04-09-2018, 10:41 AM   #2
Over This Interview Is...
 
cgtech's Avatar
Yamaha
 
Join Date: Jun 2012
Location: AZ
Posts: 11,986
Default Re: MOT-D2 motor not sitting flush on G29

I would take the motor mount plate off the axle housing and put it on the motor. (Removed with 4 bolts). This will tell you if the interference is the motor housing, or motor coupler. I have heard of motor armatures being "knocked around" during shipping.
cgtech is offline   Reply With Quote
Unread 04-09-2018, 10:47 AM   #3
Not Yet Wild
 
JakeJones8's Avatar
Yamaha
 
Join Date: May 2017
Location: Dallas, TX
Posts: 66
Default Re: MOT-D2 motor not sitting flush on G29

Thanks for the reply!

So undo the 4 bolts inside the housing? This won’t release all the fluid inside the differential will it? Lol just filled it...
JakeJones8 is offline   Reply With Quote
Unread 04-09-2018, 10:48 AM   #4
Not Yet Wild
 
JakeJones8's Avatar
Yamaha
 
Join Date: May 2017
Location: Dallas, TX
Posts: 66
Default Re: MOT-D2 motor not sitting flush on G29

Or is it the 4 bolts around the outside of the housing that make a square?
JakeJones8 is offline   Reply With Quote
Unread 04-09-2018, 11:16 AM   #5
Not Yet Wild
 
JakeJones8's Avatar
Yamaha
 
Join Date: May 2017
Location: Dallas, TX
Posts: 66
Default Re: MOT-D2 motor not sitting flush on G29

Nvm got it off... see pics. The diameter of the ring on the motor mount is too large to fit inside the casing of the new motor? Have you ever seen this before?!? I figure these are made with molds but could it have been a production issue??
JakeJones8 is offline   Reply With Quote
Unread 04-09-2018, 12:48 PM   #6
Over This Interview Is...
 
cgtech's Avatar
Yamaha
 
Join Date: Jun 2012
Location: AZ
Posts: 11,986
Default Re: MOT-D2 motor not sitting flush on G29

Don't think it's a Yamaha production issue.
cgtech is offline   Reply With Quote
Unread 04-09-2018, 01:00 PM   #7
Not Yet Wild
 
JakeJones8's Avatar
Yamaha
 
Join Date: May 2017
Location: Dallas, TX
Posts: 66
Default Re: MOT-D2 motor not sitting flush on G29

Sorry I meant Admiral Motors production issue... anyone else out there have the D2 and have the same issue or just lucky me? Haha
JakeJones8 is offline   Reply With Quote
Unread 04-09-2018, 02:32 PM   #8
BGW Sponsor
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 67,094
Default Re: MOT-D2 motor not sitting flush on G29

I'm sharing your pics with engineering at Red Hawk - we should have some info soon
scottyb is offline   Reply With Quote
Unread 04-09-2018, 02:41 PM   #9
Not Yet Wild
 
stoleno's Avatar
 
Join Date: Jun 2017
Posts: 25
Default Re: MOT-D2 motor not sitting flush on G29

Quote:
Originally Posted by JakeJones8 View Post
Sorry I meant Admiral Motors production issue... anyone else out there have the D2 and have the same issue or just lucky me? Haha


I had the same issue with mine... i got it with in an 1/8 of an inch and just sent it... seems fine


Sent from my iPhone using Tapatalk
stoleno is offline   Reply With Quote
Unread 04-09-2018, 03:12 PM   #10
BGW Sponsor
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 67,094
Default Re: MOT-D2 motor not sitting flush on G29

Quote:
Originally Posted by stoleno View Post
I had the same issue with mine... i got it with in an 1/8 of an inch and just sent it... seems fine


Sent from my iPhone using Tapatalk
That's what I'm thinking but, the customer is requesting some assurance. Thanks for your input.
scottyb is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Yamaha


Thread Tools
Display Modes


Similar Threads
Thread Forum
Flush fuel tank G9 Gas Yamaha
Oil flush?? Gas Yamaha
Tiny Tac Flush Mount Gas Club Car
Looking for Flush Mounted headlights to fit G1 Gas Yamaha
Motor set up from sitting 1989 Marathon Gas EZGO


All times are GMT -5. The time now is 02:16 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.