|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
04-09-2018, 09:16 AM | #1 |
Getting Wild
Join Date: May 2017
Location: Dallas, TX
Posts: 116
|
MOT-D2 motor not sitting flush on G29
Anyone put the Admiral MOT-D2 high speed motor on their Yamaha Drive??
I for the life of me can’t get the motor to sit flush on the differential mount (see pics). I know something is wrong because I can take the old motor and slide it on and off like butter!!! I have tried everything under the sun and it almost appears as if the inside ring of the motor housing is smaller than the outside ring on the differential mounting. It slides perfectly until the very end and just hits a brick wall. I can spin it in every direction but it never slides all the way on. Was told do not try and tighten until completly flush. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-09-2018, 09:41 AM | #2 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: MOT-D2 motor not sitting flush on G29
I would take the motor mount plate off the axle housing and put it on the motor. (Removed with 4 bolts). This will tell you if the interference is the motor housing, or motor coupler. I have heard of motor armatures being "knocked around" during shipping.
|
04-09-2018, 09:47 AM | #3 |
Getting Wild
Join Date: May 2017
Location: Dallas, TX
Posts: 116
|
Re: MOT-D2 motor not sitting flush on G29
Thanks for the reply!
So undo the 4 bolts inside the housing? This won’t release all the fluid inside the differential will it? Lol just filled it... |
04-09-2018, 09:48 AM | #4 |
Getting Wild
Join Date: May 2017
Location: Dallas, TX
Posts: 116
|
Re: MOT-D2 motor not sitting flush on G29
Or is it the 4 bolts around the outside of the housing that make a square?
|
04-09-2018, 10:16 AM | #5 |
Getting Wild
Join Date: May 2017
Location: Dallas, TX
Posts: 116
|
Re: MOT-D2 motor not sitting flush on G29
Nvm got it off... see pics. The diameter of the ring on the motor mount is too large to fit inside the casing of the new motor? Have you ever seen this before?!? I figure these are made with molds but could it have been a production issue??
|
04-09-2018, 11:48 AM | #6 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: MOT-D2 motor not sitting flush on G29
Don't think it's a Yamaha production issue.
|
04-09-2018, 12:00 PM | #7 |
Getting Wild
Join Date: May 2017
Location: Dallas, TX
Posts: 116
|
Re: MOT-D2 motor not sitting flush on G29
Sorry I meant Admiral Motors production issue... anyone else out there have the D2 and have the same issue or just lucky me? Haha
|
04-09-2018, 01:32 PM | #8 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: MOT-D2 motor not sitting flush on G29
I'm sharing your pics with engineering at Red Hawk - we should have some info soon
|
04-09-2018, 01:41 PM | #9 | |
Not Yet Wild
Join Date: Jun 2017
Posts: 31
|
Re: MOT-D2 motor not sitting flush on G29
Quote:
I had the same issue with mine... i got it with in an 1/8 of an inch and just sent it... seems fine Sent from my iPhone using Tapatalk |
|
04-09-2018, 02:12 PM | #10 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: MOT-D2 motor not sitting flush on G29
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Flush fuel tank G9 | Gas Yamaha | |||
Oil flush?? | Gas Yamaha | |||
Tiny Tac Flush Mount | Gas Club Car | |||
Looking for Flush Mounted headlights to fit G1 | Gas Yamaha | |||
Motor set up from sitting 1989 Marathon | Gas EZGO |