Logisystem controller wiring HELP needed ...

scottyb · 11-13-2008, 11:31 PM

Hello, Friends. I have an 89 CC 36v stock motor with 48v batts and 480 amp Logisystem 48v controller. Stock F&R. Link here will take you to the test section where I thought roady and I would kick this things arse in like 30 minutes. Low and behold it is still eluding me ..... I can not get her to run. Motor tests good. Batts holding 50v at this time....If you can help that would be

...Link here will take you to pics and diagrams we are using. logisystem

roady89 · 11-14-2008, 07:41 AM

Scotty, can you draw up the carts wiring and fax it to me....I don't mean the schematic I drew up, I mean the carts wiring. Go out, look at it and draw it up.

scottyb · 11-14-2008, 09:23 AM

The cart is stripped to the frame. Batteries and drive components are installed. So the opnly wires are the new ones I have connected so here is what I have been working with.....Solenoid is tested. Is there anyway the 3 small terminals on the controller could be wrong? They are not marked but, it is wired as it showed on the orig Logisytem diagram..

buckmanmike · 11-14-2008, 10:59 AM

Scotty, I used the diagram Roady posted in my resistor to controller thread. It was easy to follow and worked for my. It was on the second page of the thread. Sorry, don't know how to link you to it, but it was under the Extreme heading. Good luck, Mike

scottyb · 11-14-2008, 06:57 PM

Thanks buckman, I found it easy enough and will study it tonite...
here is the linked diagram....
http://www.buggiesgonewild.com/attac...ler-wiring.jpg
And the diagram?

I know you also had the logisystem so I have some faith this will work when I get time....I'm curious if the diagram they sent you with your controller did not work for you?

roady89 · 11-14-2008, 07:08 PM

Scotty. That diagram is for an Alltrax controller. The logisystems controller is different. I just got your email, gimme a bit to look and compare.

roady89 · 11-14-2008, 07:25 PM

Everything looks correct. One thing that does not match is connecting the 2 terminals together on the bottom of the F/R. It should be the left only stock. I would transfer attention to the throttle and power connections on the controller. I think buckmanmike had some trouble with his too in that area.

scottyb · 11-14-2008, 09:05 PM

I have had the connector bus on and off and it didn't work either way?

roady89 · 11-14-2008, 10:07 PM

Quote:

Originally Posted by scottyb

I have had the connector bus on and off and it didn't work either way?

Again, I would concentrate my efforts on the throttle and power connections on the controller. The F/R switch and main power wiring is connected properly.

Kind of a bad situation...logisystems website no longer exist so you can't get diagrams....at least last time I looked.

scottyb · 11-14-2008, 10:31 PM

Yeh, it is too bad they don't care enough about their customers to get the site working...it has been down all year. What is up with that !? Something is wrong with their diagrams? I now have a stock 95-03 48v CC diagram in hand and will prolly, try that?

I see the 48v controller has one wire hook up on the bottom........

11-13-2008, 11:31 PM	#1
scottyb lug nutz Join Date: Dec 2007 Location: So Cal Posts: 6,109	Logisystem controller wiring HELP needed ... Hello, Friends. I have an 89 CC 36v stock motor with 48v batts and 480 amp Logisystem 48v controller. Stock F&R. Link here will take you to the test section where I thought roady and I would kick this things arse in like 30 minutes. Low and behold it is still eluding me ..... I can not get her to run. Motor tests good. Batts holding 50v at this time....If you can help that would be ...Link here will take you to pics and diagrams we are using. logisystem

11-14-2008, 07:41 AM	#2
roady89 Brkn it dwn BaRnEy StYlE Join Date: Jun 2007 Location: Kaufman, Texas Posts: 3,444	Re: Logisystem controller wiring HELP needed ... Scotty, can you draw up the carts wiring and fax it to me....I don't mean the schematic I drew up, I mean the carts wiring. Go out, look at it and draw it up.
	Golf Carts \| Lifted Golf Carts \| Electric Golf Carts Custom EZGO \| B&S V-Twin \| All Sports Long Travel Lift \| 8:1 Gears \| 22" Titan AT489's \| \| \| \| \| \| \|

11-14-2008, 10:59 AM	#4
buckmanmike Gone Wild Join Date: Oct 2007 Location: Snellville, Ga. Posts: 656	Re: Logisystem controller wiring HELP needed ... Scotty, I used the diagram Roady posted in my resistor to controller thread. It was easy to follow and worked for my. It was on the second page of the thread. Sorry, don't know how to link you to it, but it was under the Extreme heading. Good luck, Mike

11-14-2008, 06:57 PM	#5
scottyb lug nutz Join Date: Dec 2007 Location: So Cal Posts: 6,109	Re: Logisystem controller wiring HELP needed ... Thanks buckman, I found it easy enough and will study it tonite... here is the linked diagram.... http://www.buggiesgonewild.com/attac...ler-wiring.jpg And the diagram? I know you also had the logisystem so I have some faith this will work when I get time....I'm curious if the diagram they sent you with your controller did not work for you?

11-14-2008, 07:08 PM	#6
roady89 Brkn it dwn BaRnEy StYlE Join Date: Jun 2007 Location: Kaufman, Texas Posts: 3,444	Re: Logisystem controller wiring HELP needed ... Scotty. That diagram is for an Alltrax controller. The logisystems controller is different. I just got your email, gimme a bit to look and compare.
	Golf Carts \| Lifted Golf Carts \| Electric Golf Carts Custom EZGO \| B&S V-Twin \| All Sports Long Travel Lift \| 8:1 Gears \| 22" Titan AT489's \| \| \| \| \| \| \|

11-14-2008, 07:25 PM	#7
roady89 Brkn it dwn BaRnEy StYlE Join Date: Jun 2007 Location: Kaufman, Texas Posts: 3,444	Re: Logisystem controller wiring HELP needed ... Everything looks correct. One thing that does not match is connecting the 2 terminals together on the bottom of the F/R. It should be the left only stock. I would transfer attention to the throttle and power connections on the controller. I think buckmanmike had some trouble with his too in that area.
	Golf Carts \| Lifted Golf Carts \| Electric Golf Carts Custom EZGO \| B&S V-Twin \| All Sports Long Travel Lift \| 8:1 Gears \| 22" Titan AT489's \| \| \| \| \| \| \|

11-14-2008, 09:05 PM	#8
scottyb lug nutz Join Date: Dec 2007 Location: So Cal Posts: 6,109	Re: Logisystem controller wiring HELP needed ... I have had the connector bus on and off and it didn't work either way?

11-14-2008, 10:31 PM	#10
scottyb lug nutz Join Date: Dec 2007 Location: So Cal Posts: 6,109	Re: Logisystem controller wiring HELP needed ... Yeh, it is too bad they don't care enough about their customers to get the site working...it has been down all year. What is up with that !? Something is wrong with their diagrams? I now have a stock 95-03 48v CC diagram in hand and will prolly, try that? I see the 48v controller has one wire hook up on the bottom........

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
logisystem	Test Post
controller needed	Electric Club Car
1986 ez go electric wiring needed	Electric EZGO
Western ID & Wiring Diagram Needed	Electric golf carts
36 volt wiring know how needed	Electric EZGO