|
Extreme DC! Extreme Electric Golf Carts! |
|
Thread Tools | Display Modes |
11-03-2013, 01:22 AM | #1 |
Not Yet Wild
Join Date: Jan 2012
Posts: 6
|
PQ torque motor, alltrax 500 won't go!!!
Installed the PQ torque motor with had solenoid and alltrax 500 for my 2008 club car precedent. Controller lights up green, shows code for club car in green, I press the pedal and it surges forward for half a second, the the controller shows red, code 6, low voltage. Voltage at controller is 49 volts, these are brand new batteries and 1/0 cables. Please help. I plan on calling PQ on Monday, but I will be out of town for a week and deer season starts the following. Really need to get this fixed tomorrow if possible. Any ideas as to what's going on?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-03-2013, 06:52 AM | #2 |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Re: Plaque torque motor, alltrax 500 won't go!!!
Re check all the wiring. Make sure the solenoid is working.
|
11-03-2013, 10:20 AM | #3 |
Not Yet Wild
Join Date: Jan 2012
Posts: 6
|
Re: Plaque torque motor, alltrax 500 won't go!!!
Checked all wiring, reset obc, and while checking solenoid, this is what I found: 49 volts on both sides without throttle pressed, once throttle is pressed, voltage on side to controller drops to 20 volts. What do I do now?
|
11-03-2013, 10:26 AM | #4 |
Not Yet Wild
Join Date: Jan 2012
Posts: 6
|
Re: Plaque torque motor, alltrax 500 won't go!!!
Title should say PQ not plaque! Sorry, I just noticed that. In no way am I bad talking PQ they were very helpful with everything so far.
|
11-04-2013, 06:52 AM | #5 |
What the ....?
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 14,934
|
Re: PQ torque motor, alltrax 500 won't go!!!
|
11-04-2013, 06:57 AM | #6 |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Re: PQ torque motor, alltrax 500 won't go!!!
Are u sure the OBC reset? Do a search on the C/C section for jumping it out and see if it works.
Does the charger turn on and work as it suppose to? |
11-04-2013, 10:40 AM | #7 |
72 volt torque monster
Join Date: Dec 2009
Location: Sorrento, FLA
Posts: 589
|
Re: Plaque torque motor, alltrax 500 won't go!!!
that's a problem, voltage should only be on battery pack side of solenoid without throttle pressed, once pressed, both sides should read the same, if not then probly a bad solenoid. Also check control wire to solenoid and verify voltage once throttle is pressed.
|
11-04-2013, 11:11 AM | #8 | |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: Plaque torque motor, alltrax 500 won't go!!!
Quote:
|
|
11-04-2013, 11:21 AM | #9 |
72 volt torque monster
Join Date: Dec 2009
Location: Sorrento, FLA
Posts: 589
|
Re: PQ torque motor, alltrax 500 won't go!!!
yea, that's true, so if resister is present, remove it from the controller side of solenoid, recheck.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
New D&D Torque Motor (4:1) - Not Seeing 40% Torque | Electric EZGO | |||
Alltrax DCX400 Speed and Torque Question | Electric EZGO | |||
GE Beast motor VS. D&D Torque motor | Electric EZGO | |||
New Alltrax 400 AXE & DnD motor | Electric EZGO | |||
01 EZ-GO PDS w/ Alltrax 400 and D&D Motor won't go! Please Help!! | Electric EZGO |